Agilent Technologies B1500A Manual de Serviço Página 451
- Página / 598
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Agilent B1500A/B1505A Programming Guide, Edition 11 4-135
Command Reference
MI
0 to ± 25 V (MFCMU) or ± 100 V (with SCUU)
Example
Statements
OUTPUT @B1500;"MDCV 9,0,5"
NOTE With the SCUU, the source module is automatically selected by the setting value.
The MFCMU is used if the base, bias, and post values are below ± 25 V (setting
resolution: 0.001 V), or the SMU is used if they are greater than ± 25 V (setting
resolution: 0.005 V).
The SMU will operate with the 100 V limited auto ranging and 20 mA compliance
settings.
MI
The MI command sets the DC current source (SMU) for the sampling measurement
(MM10). This command setting clears, and is cleared by, the MV command setting.
The specified channel starts the base current output by the measurement trigger (XE
command and so on), and changes the output value to bias after the hold time
elapses. The hold time is set by the h_base parameter of the MT command.
When multiple channels are used, channel outputs start in the order from lower to
higher channel number 101 to 1001. The channel numbers 1 to 10 correspond to the
channel numbers 101 to 1001 respectively. See Table 4-1 on page 4-16.
If the DI command is executed for this channel, the channel works as the DC current
source set by the DI command.
Execution
Conditions
If Vcomp value is greater than the allowable voltage for the interlock open
condition, the interlock circuit must be shorted.
Syntax MI chnum,irange,base,bias[,Vcomp]
Parameters chnum : SMU source channel number. Integer expression. 1 to 10 or 101 to
1001. See Table 4-1 on page 4-16.
irange : Ranging type. Integer expression. The output range will be set to the
minimum range that covers both base and bias values. For the limited
auto ranging, the instrument never uses the range less than the specified
range. See Table 4-5 on page 4-22.
base, bias : Base current and bias current (in A). Numeric expression. See Table 4-6
on page 4-23, Table 4-8 on page 4-25, or Table 4-11 on page 4-27 for
each measurement resource type. base and bias must have the same
polarity.
- Agilent B1500A/B1505A 1
- Manual Part Number 2
- Warranty 2
- Technol o gy Licenses 2
- Restricted Rights Legend 2
- For B1500A Users 3
- For B1505A Users 3
- In This Manual 4
- Contents 10
- 1 Programming Basics 19
- 10 ASSIGN @B1500 TO 717 20
- Before Starting 21
- FlexGUI Window 22
- Settings dialog box 24
- Getting Started 25
- To Reset the Agilent B1500 26
- To Read Query Response 26
- To Perform Self-Test 26
- To Perform Self-Calibration 26
- To Perform Diagnostics 27
- To Force Voltage/Current 30
- To Set the Measurement Range 32
- To Pause Command Execution 33
- To Start Measurement 33
- To F orce 0 V 33
- To Control ASU 34
- To Control SCUU 35
- To Read Error Code/Message 36
- To Read Spot Measurement Data 36
- To Read Time Stamp Data 38
- Alpha Character 40
- (A to Z, a to z) 40
- Numeric Data 41
- Terminator 42
- Special Terminator 42
- Separator 42
- Data Output Format 43
- ASCII Data Output Format 44
- Data Format 45
- Data Elements 48
- Binary Data Output Format 54
- Data Resolution 55
- Byte 1 Byte 2 Byte 3 Byte 4 59
- AB C D E F 59
- 8 Bytes Data Elements 66
- GPIB Interface Capability 73
- Status Byte 74
- Programming Tips 76
- To Confirm the Operation 77
- GOC, SOC 84
- Programming Basics 86
- 2 Remote Mode Functions 87
- Measurement Modes 89
- Voltage or current 100
- Binary Search Measurements 106
- Linear Search Measurements 108
- Sampling Measurements 110
- Quasi-static CV Measurements 113
- Capacitance Data 115
- Spot C Measurements 116
- Pulsed Spot C Measurements 117
- Pulsed Sweep CV Measurements 122
- C-f Sweep Measurements 124
- AC signal level 126
- C-t Sampling Measurements 128
- Synchronous Output 130
- Automatic Abort Function 132
- Parallel Measurement Function 134
- Program Memory 135
- Dual HCSMU 138
- SPGU Module 139
- SPGU DC bias output 140
- SPGU Channel Status 140
- PG Operation Mode 141
- Remote Mode Functions 143
- ALWG Operation Mode 145
- Module Selector 150
- External Relay Control Output 151
- SMU/PG Selector 152
- HVSMU force is 154
- connected to 154
- HVSMU Current Expander 155
- Ultra High Voltage Expander 156
- Digital I/O Port 157
- Accessories 158
- Digital I/O Internal Circuit 159
- Trigger Function 160
- Trigger Input 161
- Trigger Output 163
- Using Trigger Function 166
- To Send Trigger Using OS/OSX 167
- Start measurement 168
- Measurement completion 168
- Ext Trig In 168
- Ext Trig Out 168
- Hold time 171
- Delay time or more 171
- Step delay time or more 171
- Source trigger delay 171
- Measurement trigger delay 171
- Trig In/Out Internal Circuit 172
- Initial Settings 173
- 3 Programming Examples 179
- About Example Program Code 181
- To Start Program 181
- To Create Measurement Program 183
- High-Speed Spot Measurements 187
- Spot Measurements 190
- Pulsed Spot Measurements 193
- Staircase Sweep Measurements 196
- Pulsed Sweep Measurements 206
- ," & igcomp 218
- Programming Examples 238
- Measurement 238
- Result Example 238
- Data save completed 248
- Using Program Memory 290
- Tips to use program memory 291
- Reading Time Stamp Data 308
- Reading Binary Output Data 309
- Using Programs for 4142B 312
- 4 Command Reference 317
- Command Summary 319
- Sets the timing parameters 326
- Command Parameters 331
- Before using 1 pA range 334
- Output ranging 337
- 50 Ω range 347
- 300 kΩ range 347
- Command Reference 348
- . This function is 360
- ,abort[,post] 367
- CORRSER? 382
- ,corr,state 385
- ,corr,mode,primary,secondary 386
- DSMPLARM 390
- DSMPLFLUSH 391
- DSMPLSETUP 392
- ERHVCTST? 402
- [,option] 405
- ERPFTEMP? 413
- ERPFUHCA 413
- ERPFUHCA? 414
- ERPFUHCCAL? 414
- ERPFUHCMAX? 414
- ERPFUHCTST? 415
- INTLKVTH 425
- INTLKVTH? 425
- [,Vcomp]] 433
- [,Icomp]] or 433
- for the 481
- Example 482
- To use ASU 487
- To use SCUU 501
- 5 Error Messages 555
- Operation Error 557
- Self-test/Calibration Error 584
- 3465 IM short test failed 588
Manuais e produtos relacionados com Medição, teste e controlo Agilent Technologies B1500A
(28 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.111 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais