Agilent Technologies PSG Manual de Instruções Página 197
- Página / 362
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Command Reference
Memory Subsystem (:MEMory)
Chapter 4 183
:DELete[:NAME]
Supported All
:MEMory:DELete[:NAME] "<file name>"
This command clears the user file system of "<file name>".
*RST N/A
Range N/A
Key Entry
Delete File
Remarks Refer to “File Name Variables” on page 150 for information on the file
name syntax.
:FREE[:ALL]
Supported All
:MEMory:FREE[:ALL]?
This command returns the number of bytes left in the user file system.
*RST N/A
Range N/A
Key Entry
All
Remarks N/A
:LOAD:LIST
Supported All
:MEMory:LOAD:LIST "<file name>"
This command loads a list sweep file.
*RST N/A
Range N/A
Key Entry
Load From Selected File
Remarks N/A
- Programming Guide 1
- Contents 10
- 1 Getting Started 15
- Interfaces 17
- IO Libraries 17
- Programming Language 18
- Using GPIB 19
- GPIB Interface Terms 22
- GPIB Function Statements 23
- Local key 24
- Preset key is pressed 24
- Using LAN 28
- Utility > 30
- Using VXI-11 31
- Getting Started 32
- Chapter 118 32
- Figure 1-2 Show Devices Form 32
- Using Sockets LAN 33
- Using TELNET LAN 34
- Start > Run 35
- Using FTP 38
- Using RS-232 40
- HyperTerminal 42
- File > Properties 42
- Settings > ASCII Setup 42
- Character Format Parameters 43
- Chapter 130 44
- 2 Programming Examples 45
- Remote Off On 46
- GPIB Programming Examples 48
- Chapter 240 54
- Chapter 242 56
- Chapter 244 58
- Chapter 246 60
- Chapter 248 62
- Chapter 250 64
- Chapter 252 66
- Chapter 254 68
- Chapter 256 70
- Chapter 258 72
- Chapter 2 59 73
- Chapter 2 61 75
- Chapter 262 76
- Chapter 2 63 77
- VXI-11 Programing 79
- Chapter 2 67 81
- Chapter 268 82
- Chapter 2 73 87
- Chapter 274 88
- Chapter 2 75 89
- Chapter 276 90
- Chapter 2 77 91
- Chapter 278 92
- Chapter 2 79 93
- Chapter 280 94
- Chapter 2 81 95
- Chapter 282 96
- Chapter 2 83 97
- Chapter 284 98
- Chapter 2 85 99
- Programming Examples 100
- LAN Programming Examples 100
- Chapter 286 100
- Chapter 2 87 101
- Chapter 288 102
- Chapter 290 104
- Command Prompt 105
- Start > Programs > 105
- Chapter 292 106
- RS-232 Programming Examples 107
- Chapter 296 110
- Queries Using Agilent BASIC 111
- Queries Using VISA and C 112
- Chapter 2 99 113
- Chapter 2100 114
- 3 Programming the 115
- Overview 116
- Chapter 3 103 117
- Status Register Bit Values 118
- Determining What to Monitor 119
- Deciding How to Monitor 120
- Status Register SCPI Commands 122
- Status Byte Group 124
- Status Byte Register 125
- Chapter 3112 126
- Status Groups 127
- Standard Event Status Group 128
- Chapter 3 115 129
- Chapter 3 123 137
- Chapter 3136 150
- 4 Command Reference 151
- Command Reference Information 152
- SCPI Basics 153
- Command Syntax 154
- Command Types 156
- Command Tree 157
- Program Messages 163
- File Name Variables 164
- IEEE 488.2 Common Commands 168
- Diagnostic Info 170
- RECALL Reg Select Seq: 172
- Save Reg Save Seq[n] Reg[nn] 173
- Run Complete Self Test 175
- DCFM/DCΦM Cal 176
- :GPIB:ADDRess 177
- :LAN:HOSTname 177
- :PMETer:ADDRess 178
- :PMETer:CHANnel 179
- :PMETer:IDN 179
- :PMETer:TIMEout 180
- :SERial:BAUD 180
- :SERial:ECHO 181
- :SERial:RECeive:PACE 181
- :SERial:RESet 182
- :SERial:TOUT 182
- :SERial:TRANsmit:PACE 183
- [:CPU]:INFOrmation:BOARds 184
- [:CPU]:INFOrmation:CCOunt:PON 185
- [:CPU]:INFOrmation:OPTions 185
- [:CPU]:INFOrmation:OTIMe 186
- [:CPU]:INFOrmation:REVision 186
- [:CPU]:INFOrmation:SDATe 187
- Display Subsystem (:DISPlay) 188
- :CONTrast 189
- :INVerse 189
- [:WINDow][:STATe] 190
- Memory Subsystem (:MEMory) 191
- :CATalog:LIST 192
- :CATalog:STATe 192
- :CATalog:UFLT 193
- :CATalog[:ALL] 193
- :COPY[:NAME] 194
- :DELete:ALL 195
- :DELete:BINary 195
- :DELete:LIST 196
- :DELete:STATe 196
- :DELete:UFLT 196
- :DELete[:NAME] 197
- :FREE[:ALL] 197
- :LOAD:LIST 197
- :STATe:COMMent 198
- :STORe:LIST 198
- :CATalog 199
- Copy File 200
- Output Subsystem(:OUTPut) 203
- Status Subsystem (:STATus) 204
- :OPERation:NTRansition 205
- :OPERation:PTRansition 205
- :OPERation[:EVENt] 206
- :QUEStionable:CONDition 209
- :QUEStionable:ENABle 210
- :QUEStionable:POWer:CONDition 217
- :QUEStionable:NTRansition 217
- :QUEStionable:POWer:ENABle 218
- :QUEStionable:POWer[:EVENt] 220
- :QUEStionable:PTRansition 221
- :QUEStionable[:EVENt] 221
- System Subsystem (:SYSTem) 222
- :HELP:MODE 223
- :PON:TYPE 224
- :PRESet:ALL 225
- :PRESet:PERSistent 225
- :PRESet:TYPE 226
- :PRESet[:USER]:SAVE 226
- :SSAVer:DELay 227
- :SSAVer:MODE 227
- :SSAVer:STATe 228
- :VERSion 228
- Trigger Subsystem 229
- :INITiate[:IMMediate][:ALL] 230
- :TRIGger:OUTPut:POLarity 230
- :TRIGger[:SEQuence]:SLOPe 231
- :TRIGger[:SEQuence]:SOURce 231
- Unit Subsystem (:UNIT) 233
- :AM[1] 234
- Incr Set 235
- :AM:MODE 236
- Ext Coupling DC AC 237
- Ext Impedance 50 Ohm 600 Ohm 237
- AM Tone 2 Rate AM Stop Rate 238
- AM Sweep Rate 239
- Trigger hardkey 239
- Bus Free Run Ext Trigger Key 239
- Gaussian Uniform 240
- Positive Negative 241
- :AM[1] 242
- :AM[1] 242
- :AM[1] 243
- :AM[1] 243
- :AM[1] 244
- AM Depth Couple Off On 245
- :AM[:DEPTh]:STEP[:INCRement] 246
- :FLATness? 247
- :FLATness:LOAD 247
- :FLATness:PAIR 248
- :FLATness:POINts? 248
- :FLATness:PRESet 249
- :FLATness:STORe 249
- [:STATe] 250
- :FREQuency:FIXed 251
- :FREQuency:MODE 251
- :FREQuency:MULTiplier 252
- :FREQuency:OFFSet 252
- :FREQuency:OFFSet:STATe 253
- :FREQuency:REFerence 253
- :FREQuency:REFerence:STATe 253
- :FREQuency:STARt 254
- :FREQuency:STOP 254
- :FREQuency[:CW] 255
- :PHASe:REFerence 255
- :PHASe[:ADJust] 256
- :ROSCillator:SOURce 256
- :ROSCillator:SOURce:AUTO 257
- :FM[1] 258
- Ext Impedance 50 Ohm 600 Ohm 260
- FM Tone 2 Rate FM Stop Rate 260
- FM Sweep Rate 261
- Gaussian 263
- Positive 264
- Negative 264
- :FM[1] 265
- :FM[1] 265
- :FM[1] 266
- :FM[1] 267
- :LIST:DIRection 268
- :LIST:DWELl 269
- :LIST:DWELl:POINts 269
- :LIST:DWELl:TYPE 270
- :LIST:FREQuency 270
- :LIST:FREQuency:POINts 271
- :LIST:MANual 271
- :LIST:MODE 272
- :LIST:POWer 272
- :LIST:POWer:POINts 273
- :LIST:TRIGger:SOURce 273
- :LIST:TYPE 274
- Preset List 275
- :SWEep:DWELl 276
- :SWEep:POINts 276
- :AMPLitude 277
- :FUNCtion[1]:SWEep:RATE 278
- :FUNCtion[1]:SWEep:TRIGger 279
- :FUNCtion[1] 280
- :FUNCtion[1] 280
- :FUNCtion:NOISe 281
- :FUNCtion[1] 281
- LF Out Off On 282
- Function Generator 2 282
- :PM[1] 283
- :PM[1] 284
- ΦM Stop Rate ΦM Tone 2 Rate 286
- ΦM Sweep Rate 287
- :PM[1] 290
- :PM[1] 290
- :PM[1] 291
- :PM[1] 292
- Power Subsystem ([:SOURce]) 293
- :POWer:ALC:LEVel 294
- :POWer:ALC:SEARch 294
- :POWer:ALC:SOURce 295
- :POWer:ALC[:STATe] 296
- :POWer:ATTenuation 296
- :POWer:ATTenuation:AUTO 297
- :POWer:MODE 297
- :POWer:REFerence 298
- :POWer:REFerence:STATe 298
- :POWer:STARt 299
- :POWer:STOP 299
- Ampl Offset 300
- :PULM:INTernal[1]:DELay 302
- :PULM:INTernal[1]:DELay:STEP 303
- :PULM:INTernal[1]:FREQuency 303
- :PULM:INTernal[1]:PERiod 304
- :PULM:INTernal[1]:PWIDth 305
- :PULM:INTernal[1]:PWIDth:STEP 305
- :PULM:SOURce 306
- :PULM:SOURce:INTernal 306
- :PULM:STATe 307
- SCPI Command Compatibility 308
- Command Reference 310
- Chapter 4296 310
- Chapter 4 297 311
- Chapter 4298 312
- Chapter 4 299 313
- Chapter 4300 314
- Chapter 4 301 315
- Chapter 4302 316
- Chapter 4 303 317
- Chapter 4 307 321
- Chapter 4308 322
- Table 4-9 OS Status Byte #2 322
- Chapter 4338 352
- Numerics 353
Manuais e produtos relacionados com Geradores de energia Agilent Technologies PSG
(16 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.104 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais