Agilent Technologies 8922M Guia do Utilizador Página 368
- Página / 384
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
D-4
Appendix D - [:MM] - Measurement Fields
Commands
LLIMit:
DUNits
LLIMit:DUNits?
LLIMit:DUNits <measurement unit>
Sets/Queries the measurement Low LIMit Displayed UNits.
LLIMit:
EXCeeded
LLIMit:EXCeeded?
Queries whether the Low LIMit for the measurement was EXCeeded.
LLIMit:
RESet
LLIMit:RESet
RESet the Low LIMit exceeded state so that new limit data can be acquired.
LLIMit:
STATe
LLIMit:STATe?
LLIMit:STATe ON | OFF | 1 | 0
Sets/queries the Low LIMit STATe. Note: ON = 1 and OFF = 0.
LLIMit
[:VALue]
[:VALue]?
[:VALue] <numeric value>
Sets/queries the measurement Low LIMit VALue.
REFerence REFerence
Measurement REFerence information.
REFerence:
DUNits
REFerence:DUNits?
REFerence:DUNits <measurement unit>
Sets/queries the REFerence Displayed UNits on the front panel for the given
measurement.
REFerence:
STATe
REFerence:STATe
REFerence:STATe ON | OFF | 1 | 0
Sets/queries the REFerence STATe. Note: ON = 1 and OFF = 0.
REFerence
[:VALue]
REFerence[:VALue]?
REFerence[:VALue][<numeric value>]
Sets/queries the measurement REFerence VALue. If no <numeric value> is specified, then
the REFerence VALue will be set to the current measurement result.
- Programming Reference Guide 1
- Contents 10
- Command Guidelines 17
- Command Names 18
- Units of Measure 20
- Measurement Subsystems 21
- Syntax Diagrams 21
- Optional Commands 22
- Command Descriptions 23
- Command Name 23
- Averaging 24
- GPIB Tutorial and Examples 25
- GPIB Programming Exercises 26
- Originate a Call 27
- End the Call 27
- TX Level Changing 28
- ARFCN Changing 29
- TX Power Measurement 30
- DSP Measurements 31
- Receiver Sensitivity Test 33
- Example D - Adding Robustness 35
- Example E - Faster Testing 36
- Commands used in exercise A: 38
- Commands used in exercise B: 38
- Commands used in exercise C: 39
- Example Programs 40
- Test List 41
- Sample Output 42
- Program 1 43
- Program 2 53
- Program 3 64
- Transient Settling Times 74
- AF Analyzer Subsystem 79
- DEMPhasis 82
- DEMPhasis:GAIN 82
- DETector 82
- DETector:PKLocation 83
- DETector:SETTling 83
- ELResistor 83
- INPut:GAIN 85
- NOTCh:GAIN 85
- SPEaker:MODE 86
- SPEaker:VOLume 86
- AF Generator Subsystem 87
- AMPLitude 89
- COUPling 89
- Audio Frequency Commands 91
- DISTortion 95
- Bit Error Test Subsystem 100
- LOOPback:LDELay 101
- LOOPback:LDELay:MODE 101
- Syntax BETest:TYPE<n>? 102
- Bit Error Test Commands 103
- (Measure Subsystem) 103
- Continued Over 104
- BESelect 106
- BERRor:COUNt 106
- BERRor:ICOunt 106
- BERRor:IRATio 107
- BERRor:RATio 107
- CRC:COUNt 108
- CRC:ICOunt 108
- CRC:IRATio 108
- CRC:RATio 109
- FERasure:COUNt 109
- FERasure:ICOunt 109
- FERasure:IRATio 110
- FERasure:RATio 110
- FLSelect 110
- IBTested 111
- Cell Configuration Subsystem 113
- Cell Configuration Subsystem 114
- ABCCh:BCC 119
- CCHannel 119
- CCHannel:SDCCH8:ARFCn 120
- CCHannel:SDCCH8:TSLot 120
- MA1:IOFFset 121
- MA2:IOFFset 122
- [:GSM900]:BA 122
- [:GSM900]:CA 123
- [:GSM900]:MA1 123
- [:GSM900]:MA1:IOFFset 123
- [:GSM900]:MA2 124
- [:GSM900]:MA2:IOFFset 124
- LAI:MCCode 124
- LAI:MNCode 125
- LAI:LACode 125
- SCELl:ARFCn 125
- SCELl:BCC 125
- SCELl:NCC 126
- Cell Control Subsystem 127
- AUDio:DAI:ATESt 134
- AUDio:DAI:NORMal 134
- AUDio:LOOPback 134
- AUDio:LOOPback:FAST 134
- AUDio:LOOPback:FE 134
- AUDio:LOOPback:OFF 135
- AUDio:LOOPback:NOFE 135
- AUDio:SPEech:CONFigure 135
- AUDio:SPEech:EDELay 136
- AUDio:SPEech:GAIN 136
- AUDio:SPEech:PRBS:PATTern 136
- CALL:CONNect 137
- CALL:COUNt:BSYNc 137
- CALL:COUNt:DERRor 137
- CALL:COUNt:PAGE 137
- CALL:COUNt:RACH 138
- CALL:COUNt:RESet 138
- CALL:END 138
- CALL:LIMit 138
- CALL:ORIGinate 139
- CALL:PAGing 139
- CALL:RECeive 139
- CALL:SIGNaling 140
- CALL:TCH:ARFCn 140
- CALL:TCH:TSLot 140
- CALL:STATus:CALLer 140
- CALL:STATus:CIPHering[:STATe] 141
- CALL:STATus:MM[:STATe] 141
- CALL:STATus:RR[:STATe] 142
- CALL:STATus:STATe 142
- CALL:STATus:TCH:ARFCn 142
- CALL:STATus:TCH:MALLocation 143
- CALL:STATus:TCH:MODE 143
- CALL:STATus:TCH:TSLot 143
- CALL:STATus:TCH:TYPE 143
- CALL:TCHControl 144
- CALL:TCHControl:EXECute 144
- MS:DRX[:STATe] 145
- MS:DTX[:STATe] 145
- MS:TADVance 145
- MS:TADVance:MODE 145
- MS:TLEVel 146
- TCH1 or TCH2:ARFCn 146
- TCH1 or TCH2:MALLocation 146
- TCH1 or TCH2:MODE 146
- TCH1 or TCH2:TSLot 147
- TCH1 or TCH2:TYPE 147
- Configure Subsystem 149
- Configure Subsystem 150
- BADDress 155
- COMPatible 156
- INTensity 156
- OFLevel:MODE 156
- OFLevel:AUXout 157
- OFLevel:RFINout 157
- OFLevel:AUXin 157
- OPERation:AUTO 158
- OPERation:HOLD 158
- PRINt:ADDRess 158
- PRINt:DESTination 159
- PRINt:FFENd 159
- PRINt:FFSTart 159
- PRINt:LINes 159
- PRINt:PRINter 160
- PRINt:TITle 160
- RFIMpedance 160
- ROSCillator:CALibrate 161
- ROSCillator[:FREQuency] 161
- ROSCillator:OFFset 161
- ROSCillator:TUNing 161
- SPORt:BAUD 162
- SPORt:DATA 162
- SPORt:IBECho 162
- SPORt:PARity 163
- SPORt:RPACe 163
- SPORt:SIN 163
- SPORt:STOP 164
- SPORt:XPACe 164
- CW Subsystem 165
- Syntax CW:PMZero 166
- Options Not Applicable 166
- FREQuency[:ABSolute] 169
- FREQuency:ERRor 169
- FREQuency:SELect 169
- Syntax MEASure:CW:POWer? 170
- DISPlay Subsystem 171
- [:SCReen] 173
- BETest:MNUMber:LEFT 173
- BETest:MNUMber:RIGHt 173
- CELL:SACCh:ACEL1 173
- CELL:TCH[:SELect] 174
- DSPanalyzer:AMPLitude:MASK 174
- DSPanalyzer:VIEW 174
- MSYNc:BURSt:NUMBer 175
- ORFSpectrum:VIEW 175
- PULSe:VIEW 176
- SANalyzer:CONTrol 176
- DSP Analyzer Subsystem 177
- AMPLitude:MARKer:POSition:MID 179
- AMPLitude:PMZero 179
- AMPLitude:TIME 180
- DBITs:TPOLarity 180
- PHASe:MARKer:POSition 180
- PHASe:MIDamble 180
- DSP Analyzer Commands 181
- [:AMPLitude]:AMPLitude 184
- [:AMPLitude]:MARKer:LEVEL:MID 185
- [:AMPLitude]:MARKer:TIME:FALL 186
- [:AMPLitude]:MARKer:TIME:MID 186
- [:AMPLitude]:MARKer:TIME:RISE 187
- [:AMPLitude]:MSUMmary 187
- [:AMPLitude]:NPFLatness 188
- [:AMPLitude]:PPFLatness 188
- [:AMPLitude]:PTCPower 188
- [:AMPLitude]:TRACe 189
- DBITs:TAGS 189
- FMERrors 190
- PHASe[:ERRor]:FREQuency 190
- PHASe[:ERRor]:PEAK 191
- PHASe[:ERRor]:RMS 191
- PHASe:MARKer:ERRor 192
- PHASe:MARKer:TIME 192
- PHASe:MBURst 192
- PHASe:MBURst:COUNt 193
- PHASe:MBURst:DONE 193
- PHASe:MBURst:ERRors 193
- PHASe:TRACe 193
- (no spaces) 197
- DATA <data entry> 198
- TIMEout:MS:XON 198
- TIMEout:MS:RESPonse 199
- Fast Bit Error Test 201
- RFGenerator:ATSLot 204
- BERRor:ICOUnt 207
- FTCPower[:POWer] 210
- Hop Control Subsystem 211
- ADDRess:NEXT 214
- ADDRess:RESet 214
- ADDRess:SOURce 214
- Options ‘ARM’ 218
- IEEE 488.2 Common Commands 219
- *CLS (Clear Status) 220
- *ESE (Event Status Enable) 221
- *ESR? (Event Status Register) 222
- *IDN? (Identification Number) 223
- *OPC (Operation Complete) 224
- Query Syntax *OPT? 225
- *RCL (Recall) 226
- *RST (Reset) 227
- *SAV (Save) 228
- *SRE (Service Request Enable) 229
- *STB? (Status Byte) 230
- *TST? (Test) 231
- *WAI (Wait) 232
- LOGGing Subsystem 233
- DATA:FLUSh 235
- DATA:CLEar 235
- Syntax LOGGing:STATe? 236
- Options ’LOG’ 236
- Measurement Sync Subsystem 237
- BURSt:LENGth 239
- BURSt:SPSPosition 239
- BURSt:TQUalifier 239
- BURSt:TYPE 240
- BURSt:UDSPattern 240
- SYNC:BSELect 240
- SYNC:MODE 241
- Mobile Station Commands 243
- MS:TERRor 245
- SACCh:ACEL1:ARFCn 245
- SACCh:ACEL1:BCC 245
- SACCh:ACEL1:NCC 245
- SACCh:ACEL1:RLEVel 246
- SACCh:FULL:RLEVel 246
- SACCh:FULL:RQUality 246
- SACCh:PARTial:RLEVel 246
- SACCh:PARTial:RQUality 246
- SACCh:RESet 247
- SACCh:TADVance 247
- SACCh:TLEVel 247
- MS Information Subsystem 249
- CIPHering:AMODe 251
- CIPHering:KC 251
- CIPHering:KI 252
- CIPHering:RAND 252
- CIPHering:SRES 252
- CIPHering[:STATe] 252
- MS:ATTach 253
- MS:CMARk:PCLass? 253
- MS:CMARk:REVision? 253
- MS:CMARk:BAND? 253
- MS:IMEI:REQuest 254
- MS:IMEI? 254
- MS:IMSI:SPAGing 254
- MS:IMSI? 254
- MS:LAI:LACode? 254
- MS:LAI:MCCode? 255
- MS:LAI:MNCode? 255
- MS:ONUMber? 255
- MS:PAGPer 255
- MS:SRES? 255
- [:PAGing]:IMSIdentity 256
- [:PAGing]:TMSI:REALlocation 256
- [:PAGing]:TMSI:STATe 256
- OSCilloscope Subsystem 257
- MARKer:NPEak 259
- MARKer:PPEak 259
- MARKer:POSition 259
- SCALe:TIME 260
- SCALe:VERTical:AM 260
- SCALe:VERTical:FM 260
- SCALe:VERTical:OFFSet 261
- SCALe:VERTical:VOLTs 261
- TRIGger:LEVel 261
- TRIGger:MODE 262
- TRIGger:PRETrigger 262
- TRIGger:RESet 262
- TRIGger:SENSe 263
- TRIGger:SOURce 263
- TRIGger:TYPE 263
- MARKer:LEVel:AM 267
- MARKer:LEVel:FM 267
- MARKer:LEVel:VOLTs 267
- MARKer:TIME 268
- Output RF Spectrum Subsystem 269
- FREQuency:OFFSet 271
- SACalibrate 272
- Output RF Spectrum Commands 273
- MARKer:LEVel 275
- [:POWer] 276
- PULSe On/Off Ratio Subsystem 279
- MARKer[:POSition]:FALL 281
- MARKer[:POSition]:RISE 281
- MARKer:OPOSition:FALL 281
- MARKer:OPOSition:RISE 282
- Pulse On/Off Ratio Commands 283
- MARKer:LEVel:FALL 285
- MARKer:LEVel:RISE 286
- MARKer:TIME:FALL 286
- MARKer:TIME:RISE 287
- OORatio:FALL 287
- OORatio:RISE 287
- Syntax MEASure:PULSe:SSTatus? 288
- TRACe:FALL 289
- TRACe:RISE 289
- RF Analyzer Subsystem 291
- AGC:CALibrate 294
- AGC:DVALue 294
- AGC:MODE 294
- AMPLitude1 294
- AMPLitude2 295
- [:AMPLitude]:ACCuracy 295
- [:AMPLitude]:CONTrol 295
- FREQuency 296
- FREQuency:GTIMe 296
- FREQuency:HMEas 296
- RF Generator Subsystem 299
- AMPLitude1:ATTenuation[:AUTO] 301
- AMPLitude2:ATTenuation[:AUTO] 301
- MODulation:DCAM 302
- MODulation:DCAM:DVALue 303
- MODulation:GMSK 303
- MODulation:PULSe 303
- MODulation:PULSe:MODE 304
- SMS Cell Broadcast Subsystem 305
- MESS1 or MESS2:CODE 308
- MESS1 or MESS2:UPDate 308
- MESS1 or MESS2:IDENtifier 309
- MESS1 or MESS2:LANGuage 309
- Spectrum Analyzer Subsystem 311
- ATTenuator 314
- ATTenuator:MODE 314
- ATTenuator2 314
- CFRequency 315
- MARKer:CFRequency 315
- MARKer:PEAK 315
- MARKer:RLEVel 316
- TRACe:MHOLd 317
- Spectrum Analyzer Commands 319
- MARKer:FREQuency 321
- Status Subsystem 323
- EMMI Status Register 328
- Event register bit def 328
- CONDition 329
- NTRanistion 329
- PTRanistion 330
- System Subsystem 331
- SYSTem[:ERRor] 332
- Tests Subsystem 333
- COMMent1 335
- COMMent2 335
- CONFigure? 335
- EXECution:DESTination 336
- EXECution:FAILure 336
- EXECution:HEADing1 337
- EXECution:HEADing2 337
- EXECution:RESults 338
- EXECution:RUN 339
- FREQuency? 339
- LIBRary? 340
- PARMameter? 340
- PROCedure:AUTOstart 340
- PROCedure:LOCation 341
- PROCedure:NAME 341
- PROCedure:PRINt:CONFigure 341
- PROCedure:PRINt:FREQuency 341
- PROCedure:PRINt:PARameter 342
- PROCedure:PRINt:SEQuence 342
- PROCedure:PRINt:SPEC 342
- PROCedure:RUN 342
- SEQNumber? 343
- Trigger Subsystem 345
- BETest:MODE 349
- DDEMod:ADJMode 349
- DDEMod:ASTate 349
- DDEMod:SOURce 350
- HTCH:ARFCn[:SPECific] 351
- HTCH:ARFCn:AUTO 351
- [:IMMediate] 351
- MODE[:DSP] 352
- MODE:RETRigger 352
- UMEMory:SOURce 353
- UMEMory:STATus 354
- Numeric Fields 357
- Commands 359
- Numeric (less MODE) 361
- REFerence:STATe? 372
- REFerence[:VALue]? 372
- Using Averaging 373
- Using Meters 377
- Fields Using Multi-Burst 381
Manuais e produtos relacionados com Redes Agilent Technologies 8922M
Redes Agilent Technologies 81680A Guia do Utilizador
(112 páginas)
(112 páginas)
Redes Agilent Technologies E6392B Guia do Utilizador
(206 páginas)
(206 páginas)
Redes Agilent Technologies 8922S Guia do Utilizador
(100 páginas)
(100 páginas)
Redes Agilent Technologies 8922S Especificações
(244 páginas)
(244 páginas)
Redes Agilent Technologies E6392B Especificações
(197 páginas)
(197 páginas)
Redes Agilent Technologies 1100 Series Manual de Serviço
(318 páginas)
(318 páginas)
Redes Agilent Technologies E6474A Guia do Utilizador
(224 páginas)
(224 páginas)
Redes Agilent Technologies E6701A Guia do Utilizador
(251 páginas)
(251 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais