Agilent Technologies InfiniiVision 3000 DSO-X 3054A Manual de Serviço Página 147
- Página / 970
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Common (*) Commands 5
Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide 147
See Also • "Introduction to Common (*) Commands" on page 127
• "*SRE (Service Request Enable)" on page 144
Table 58 Status Byte Register (STB)
Bit Name Description When Set (1 = High = True), Indicates:
7 OPER Operation Status Register An enabled condition in the Operation Status
Register (OPER) has occurred.
6 RQS Request Service When polled, that the device is requesting service.
MSS Master Summary Status When read (by *STB?), whether the device has a
reason for requesting service.
5 ESB Event Status Bit An enabled condition in the Standard Event Status
Register (ESR) has occurred.
4 MAV Message Available There are messages in the Output Queue.
3 --- --- (Not used, always 0.)
2 MSG Message An advisory has been displayed on the
oscilloscope.
1 USR User Event An enabled user event condition has occurred.
0 TRG Trigger A trigger has occurred.
NOTE
To read the instrument's status byte with RQS reported on bit 6, use the interface Serial
Poll.
- Agilent InfiniiVision 1
- 3000 X-Series 1
- Oscilloscopes 1
- In This Book 3
- Contents 7
- 10 :CHANnel<n> Commands 10
- 11 :DEMO Commands 10
- 12 :DIGital<d> Commands 10
- 13 :DISPlay Commands 10
- 15 :FUNCtion Commands 11
- 16 :HARDcopy Commands 11
- 14 :EXTernal Trigger Commands 11
- 17 :LISTer Commands 12
- 18 :MARKer Commands 12
- 19 :MEASure Commands 12
- 20 :MTESt Commands 13
- 21 :POD Commands 14
- 22 :RECall Commands 14
- 23 :SAVE Commands 14
- 24 :SBUS<n> Commands 15
- 25 :SEARch Commands 17
- 26 :SYSTem Commands 18
- 27 :TIMebase Commands 19
- 28 :TRIGger Commands 19
- 29 :WAVeform Commands 21
- 30 :WGEN Commands 21
- 31 :WMEMory<r> Commands 21
- 33 Error Messages 23
- 34 Status Reporting 23
- 35 Synchronizing Acquisitions 23
- 37 Programming Examples 24
- What's New 25
- 1 What's New 26
- Version 1.00 at Introduction 27
- Obsolete 31
- Commands 31
- Discontinued 31
- Setting Up 33
- 2 Setting Up 34
- Using the LAN Interface 35
- Using the GPIB Interface 36
- Setting Up 2 37
- Address 39
- Click Test Connection 39
- Getting Started 43
- Initializing 44
- Capturing Data 44
- Analyzing Captured Data 45
- Programming the Oscilloscope 46
- 3 Getting Started 48
- Getting Started 3 49
- Ensure New Data is Collected 50
- Checking Instrument Status 54
- Telnet Sockets 55
- Commands Quick Reference 57
- Command Summary 58
- 4 Commands Quick Reference 100
- NR3 format 119
- Syntax Elements 121
- Commands Quick Reference 4 123
- Common (*) Commands 125
- 5 Common (*) Commands 126
- *CLS (Clear Status) 129
- Common (*) Commands 5 131
- *IDN (Identification Number) 134
- *LRN (Learn Device Setup) 135
- *OPC (Operation Complete) 136
- *OPT (Option Identification) 137
- *RCL (Recall) 139
- *RST (Reset) 140
- *SAV (Save) 143
- *SRE (Service Request Enable) 144
- <mask><NL> 145
- *STB (Read Status Byte) 146
- *TRG (Trigger) 148
- *TST (Self Test) 149
- *WAI (Wait To Continue) 150
- Root (:) Commands 151
- 6 Root (:) Commands 152
- :ACTivity 155
- :AER (Arm Event Register) 156
- :AUToscale 157
- :AUToscale:AMODE 159
- :AUToscale:CHANnels 160
- :AUToscale:FDEBug 161
- :DIGitize 163
- :MTEenable <mask> 165
- :MTEenable? 165
- <value><NL> 165
- :MTERegister[:EVENt]? 167
- :OPEE <mask> 169
- :OPERegister:CONDition? 171
- :OPERegister[:EVENt]? 173
- :OVLRegister? 177
- Root (:) Commands 6 179
- (see page 860) 181
- Query Syntax 181
- Return Format: 181
- :TER (Trigger Event Register) 185
- :ACQuire Commands 187
- 7 :ACQuire Commands 188
- :ACQuire:COMPlete 189
- :ACQuire:COUNt 190
- :ACQuire:MODE 191
- :ACQuire:POINts 192
- :ACQuire:SEGMented:ANALyze 193
- :ACQuire:SEGMented:COUNt 194
- :ACQuire:SEGMented:INDex 195
- :ACQuire Commands 7 197
- :ACQuire:SRATe 198
- :ACQuire:TYPE 199
- :BUS<n> Commands 201
- 8 :BUS<n> Commands 202
- :BUS<n>:BIT<m> 203
- :BUS<n>:BITS 204
- :BUS<n> Commands 8 205
- :BUS<n>:CLEar 206
- :BUS<n>:DISPlay 207
- :BUS<n>:LABel 208
- :BUS<n>:MASK 209
- :CALibrate Commands 211
- 9 :CALibrate Commands 212
- :CALibrate:DATE 213
- :CALibrate:LABel 214
- :CALibrate:OUTPut 215
- :CALibrate:PROTected 216
- :CALibrate:STARt 217
- :CALibrate:STATus 218
- :CALibrate:TEMPerature 219
- :CALibrate:TIME 220
- :CHANnel<n> Commands 221
- :CHANnel<n> Commands 10 223
- :CHANnel<n>:BWLimit 224
- :CHANnel<n>:COUPling 225
- :CHANnel<n>:DISPlay 226
- :CHANnel<n>:IMPedance 227
- :CHANnel<n>:INVert 228
- :CHANnel<n>:LABel 229
- :CHANnel<n>:OFFSet 230
- :CHANnel<n>:PROBe 231
- :CHANnel<n>:PROBe:ID 233
- :CHANnel<n>:PROBe:SKEW 234
- :CHANnel<n>:PROBe:STYPe 235
- :CHANnel<n>:PROTection 236
- :CHANnel<n>:RANGe 237
- :CHANnel<n>:SCALe 238
- :CHANnel<n>:UNITs 239
- :CHANnel<n>:VERNier 240
- :DEMO Commands 241
- :DEMO:FUNCtion 242
- Demo Signal 244
- :DEMO:FUNCtion:PHASe:PHASe 245
- :DEMO:OUTPut 246
- :DIGital<d> Commands 247
- :DIGital<d>:DISPlay 249
- :DIGital<d>:LABel 250
- :DIGital<d>:POSition 251
- :DIGital<d>:SIZE 252
- :DIGital<d>:THReshold 253
- :DISPlay Commands 255
- :DISPlay:CLEar 257
- :DISPlay:DATA 258
- :DISPlay:LABel 259
- :DISPlay:LABList 260
- :DISPlay:PERSistence 261
- :DISPlay:VECTors 262
- :EXTernal Trigger Commands 263
- :EXTernal:BWLimit 264
- :EXTernal:PROBe 265
- :EXTernal:RANGe 266
- :EXTernal:UNITs 267
- :FUNCtion Commands 269
- :FUNCtion Commands 15 271
- :FUNCtion:CENTer 272
- :FUNCtion:DISPlay 273
- :FUNCtion:GOFT:OPERation 274
- :FUNCtion:GOFT:SOURce1 275
- :FUNCtion:GOFT:SOURce2 276
- :FUNCtion:OFFSet 277
- :FUNCtion:OPERation 278
- :FUNCtion:RANGe 279
- :FUNCtion:REFerence 280
- :FUNCtion:SCALe 281
- :FUNCtion:SOURce1 282
- :FUNCtion:SOURce2 283
- :FUNCtion:SPAN 284
- :FUNCtion:WINDow 285
- :HARDcopy Commands 287
- :HARDcopy:AREA 289
- :HARDcopy:APRinter 290
- :HARDcopy:FACTors 291
- :HARDcopy:FFEed 292
- :HARDcopy:INKSaver 293
- :HARDcopy:LAYout 294
- :HARDcopy:NETWork:ADDRess 295
- :HARDcopy:NETWork:APPLy 296
- :HARDcopy:NETWork:DOMain 297
- :HARDcopy:NETWork:PASSword 298
- :HARDcopy:NETWork:SLOT 299
- :HARDcopy:NETWork:USERname 300
- :HARDcopy:PALette 301
- :HARDcopy:PRINter:LIST 302
- :HARDcopy:STARt 303
- :LISTer Commands 305
- :LISTer:DATA 306
- :LISTer:DISPlay 307
- :LISTer:REFerence 308
- :MARKer Commands 309
- :MARKer:MODE 311
- :MARKer:X1Position 312
- :MARKer:X1Y1source 313
- :MARKer:X2Position 314
- :MARKer:X2Y2source 315
- :MARKer:XDELta 316
- :MARKer:Y1Position 317
- :MARKer:Y2Position 318
- :MARKer:YDELta 319
- :MEASure Commands 321
- :MEASure Commands 19 331
- :MEASure:ALL 332
- :MEASure:AREa 333
- :MEASure:BWIDth 334
- :MEASure:CLEar 335
- :MEASure:COUNter 336
- :MEASure:DEFine 337
- :MEASure:DELay 340
- :MEASure:DUTYcycle 342
- :MEASure:FALLtime 343
- :MEASure:FREQuency 344
- :MEASure:NEDGes 345
- :MEASure:NPULses 346
- :MEASure:NWIDth 347
- :MEASure:OVERshoot 348
- :MEASure:PEDGes 350
- :MEASure:PERiod 351
- :MEASure:PHASe 352
- :MEASure:PPULses 353
- :MEASure:PREShoot 354
- :MEASure:PWIDth 355
- :MEASure:RESults 356
- :MEASure:RISetime 359
- :MEASure:SDEViation 360
- :MEASure:SHOW 361
- :MEASure:SOURce 362
- Example Code 363
- :MEASure:STATistics 364
- :MEASure:STATistics:INCRement 365
- :MEASure:STATistics:RESet 366
- :MEASure:TEDGe 367
- :MEASure:TVALue 369
- :MEASure:VAMPlitude 371
- :MEASure:VAVerage 372
- :MEASure:VBASe 373
- :MEASure:VMAX 374
- :MEASure:VMIN 375
- :MEASure:VPP 376
- :MEASure:VRATio 377
- :MEASure:VRMS 378
- :MEASure:VTIMe 379
- :MEASure:VTOP 380
- :MEASure:WINDow 381
- :MEASure:XMAX 382
- :MEASure:XMIN 383
- :MTESt Commands 385
- :MTESt Commands 20 389
- :MTESt:ALL 390
- :MTESt:AMASk:CREate 391
- :MTESt:AMASk:SOURce 392
- :MTESt:AMASk:UNITs 393
- :MTESt:AMASk:XDELta 394
- :MTESt:AMASk:YDELta 395
- :MTESt:COUNt:FWAVeforms 396
- :MTESt:COUNt:RESet 397
- :MTESt:COUNt:TIME 398
- :MTESt:COUNt:WAVeforms 399
- :MTESt:DATA 400
- :MTESt:DELete 401
- :MTESt:ENABle 402
- :MTESt:LOCK 403
- :MTESt:RMODe 404
- :MTESt:RMODe:FACTion:MEASure 405
- :MTESt:RMODe:FACTion:PRINt 406
- :MTESt:RMODe:FACTion:SAVE 407
- :MTESt:RMODe:FACTion:STOP 408
- :MTESt:RMODe:SIGMa 409
- :MTESt:RMODe:TIME 410
- :MTESt:RMODe:WAVeforms 411
- :MTESt:SCALe:BIND 412
- :MTESt:SCALe:X1 413
- :MTESt:SCALe:XDELta 414
- :MTESt:SCALe:Y1 415
- :MTESt:SCALe:Y2 416
- :MTESt:SOURce 417
- :MTESt:TITLe 418
- :POD Commands 419
- :POD<n>:DISPlay 421
- :POD<n>:SIZE 422
- :POD<n>:THReshold 423
- :RECall Commands 425
- :RECall:FILename 427
- :RECall:MASK[:STARt] 428
- :RECall:PWD 429
- :RECall:SETup[:STARt] 430
- :RECall Commands 22 431
- :SAVE Commands 433
- :SAVE Commands 23 435
- :SAVE:FILename 436
- :SAVE:IMAGe[:STARt] 437
- :SAVE:IMAGe:FACTors 438
- :SAVE:IMAGe:FORMat 439
- :SAVE:IMAGe:INKSaver 440
- :SAVE:IMAGe:PALette 441
- :SAVE:LISTer[:STARt] 442
- :SAVE:MASK[:STARt] 443
- :SAVE:PWD 444
- :SAVE:SETup[:STARt] 445
- :SAVE:WAVeform[:STARt] 446
- :SAVE:WAVeform:FORMat 447
- :SAVE:WAVeform:LENGth 448
- :SAVE:WAVeform:SEGMented 449
- :SAVE:WMEMory:SOURce 450
- :SAVE:WMEMory[:STARt] 451
- :SBUS<n> Commands 453
- :SBUS<n>:DISPlay 456
- :SBUS<n>:MODE 457
- :SBUS<n>:CAN Commands 458
- :SBUS<n> Commands 24 461
- :SBUS<n>:CAN:SOURce 468
- :SBUS<n>:CAN:TRIGger 469
- :SBUS<n>:I2S Commands 475
- :SBUS<n>:I2S:ALIGnment 477
- :SBUS<n>:I2S:BASE 478
- :SBUS<n>:I2S:RWIDth 480
- :SBUS<n>:I2S:TRIGger 484
- :SBUS<n>:I2S:TWIDth 492
- :SBUS<n>:I2S:WSLow 493
- :SBUS<n>:IIC Commands 494
- :SBUS<n>:IIC:ASIZe 495
- :SBUS<n>:LIN Commands 504
- :SBUS<n>:LIN:PARity 506
- :SBUS<n>:LIN:SOURce 509
- :SBUS<n>:LIN:STANdard 510
- :SBUS<n>:LIN:SYNCbreak 511
- :SBUS<n>:LIN:TRIGger 512
- :SBUS<n>:LIN:TRIGger:ID 513
- :SBUS<n>:SPI Commands 518
- :SBUS<n>:SPI:BITorder 520
- :SBUS<n>:SPI:FRAMing 523
- :SBUS<n>:SPI:WIDTh 534
- :SBUS<n>:UART Commands 535
- :SBUS<n>:UART:BASE 538
- :SBUS<n>:UART:BAUDrate 539
- :SBUS<n>:UART:BITorder 540
- :SBUS<n>:UART:FRAMing 545
- :SBUS<n>:UART:PARity 546
- :SBUS<n>:UART:POLarity 547
- :SBUS<n>:UART:SOURce:RX 548
- :SBUS<n>:UART:SOURce:TX 549
- :SBUS<n>:UART:WIDTh 556
- :SEARch Commands 557
- General :SEARch Commands 558
- :SEARch:COUNt 559
- :SEARch:MODE 560
- :SEARch:STATe 561
- :SEARch:EDGE Commands 562
- :SEARch:EDGE:SLOPe 563
- :SEARch:EDGE:SOURce 564
- :SEARch:GLITch Commands 565
- :SEARch:GLITch:GREaterthan 566
- :SEARch:GLITch:LESSthan 567
- :SEARch:GLITch:POLarity 568
- :SEARch:GLITch:QUALifier 569
- :SEARch:GLITch:RANGe 570
- :SEARch:GLITch:SOURce 571
- :SEARch:RUNT Commands 572
- :SEARch:RUNT:POLarity 573
- :SEARch:RUNT:QUALifier 574
- :SEARch:RUNT:SOURce 575
- :SEARch:RUNT:TIME 576
- :SEARch:TRANsition Commands 577
- :SEARch:TRANsition:QUALifier 578
- :SEARch:TRANsition:SLOPe 579
- :SEARch:TRANsition:SOURce 580
- :SEARch:TRANsition:TIME 581
- :SEARch:SERial:CAN Commands 582
- :SEARch Commands 25 583
- :SEARch:SERial:CAN:PATTern:ID 585
- :SEARch:SERial:CAN:MODE 587
- :SEARch:SERial:I2S Commands 588
- :SEARch:SERial:I2S:AUDio 589
- :SEARch:SERial:I2S:MODE 590
- :SEARch:SERial:I2S:RANGe 593
- :SEARch:SERial:IIC Commands 594
- :SEARch:SERial:IIC:MODE 595
- :SEARch:SERial:IIC:QUALifier 600
- :SEARch:SERial:LIN Commands 601
- :SEARch:SERial:LIN:ID 602
- :SEARch:SERial:LIN:MODE 603
- :SEARch:SERial:SPI Commands 607
- :SEARch:SERial:SPI:MODE 608
- :SEARch:SERial:UART Commands 611
- :SEARch:SERial:UART:DATA 612
- :SEARch:SERial:UART:MODE 613
- :SEARch:SERial:UART:QUALifier 614
- :SYSTem Commands 615
- :SYSTem:DATE 617
- :SYSTem:DSP 618
- :SYSTem:ERRor 619
- :SYSTem:LOCK 620
- :SYSTem:PRESet 621
- :SYSTem:PROTection:LOCK 624
- :SYSTem:SETup 625
- :SYSTem:TIME 627
- :TIMebase Commands 629
- :TIMebase:MODE 631
- :TIMebase:POSition 632
- :TIMebase:RANGe 633
- :TIMebase:REFerence 634
- :TIMebase:SCALe 635
- :TIMebase:VERNier 636
- :TIMebase:WINDow:POSition 637
- :TIMebase:WINDow:RANGe 638
- :TIMebase:WINDow:SCALe 639
- :TRIGger Commands 641
- General :TRIGger Commands 643
- :TRIGger:HFReject 644
- :TRIGger:HOLDoff 645
- :TRIGger:LEVel:HIGH 646
- :TRIGger:LEVel:LOW 647
- :TRIGger:MODE 648
- :TRIGger:NREJect 649
- :TRIGger:SWEep 650
- :TRIGger:EBURst Commands 651
- :TRIGger:EBURst:COUNt 652
- :TRIGger:EBURst:IDLE 653
- :TRIGger:EBURst:SLOPe 654
- :TRIGger:EBURst:SOURce 655
- :TRIGger[:EDGE] Commands 656
- :TRIGger[:EDGE]:COUPling 657
- :TRIGger[:EDGE]:LEVel 658
- :TRIGger[:EDGE]:REJect 659
- :TRIGger[:EDGE]:SLOPe 660
- :TRIGger[:EDGE]:SOURce 661
- :TRIGger:GLITch Commands 662
- :TRIGger:GLITch:GREaterthan 664
- :TRIGger:GLITch:LESSthan 665
- :TRIGger:GLITch:LEVel 666
- :TRIGger:GLITch:POLarity 667
- :TRIGger:GLITch:QUALifier 668
- :TRIGger:GLITch:RANGe 669
- :TRIGger:GLITch:SOURce 670
- :TRIGger:PATTern Commands 671
- :TRIGger:PATTern 672
- :TRIGger Commands 28 673
- :TRIGger:PATTern:FORMat 674
- :TRIGger:PATTern:GREaterthan 675
- :TRIGger:PATTern:LESSthan 676
- :TRIGger:PATTern:QUALifier 677
- :TRIGger:PATTern:RANGe 679
- :TRIGger:RUNT Commands 680
- :TRIGger:RUNT:POLarity 681
- :TRIGger:RUNT:QUALifier 682
- :TRIGger:RUNT:SOURce 683
- :TRIGger:RUNT:TIME 684
- :TRIGger:SHOLd Commands 685
- :TRIGger:SHOLd:SLOPe 686
- :TRIGger:SHOLd:SOURce:CLOCk 687
- :TRIGger:SHOLd:SOURce:DATA 688
- :TRIGger:SHOLd:TIME:HOLD 689
- :TRIGger:SHOLd:TIME:SETup 690
- :TRIGger:TRANsition Commands 691
- :TRIGger:TRANsition:QUALifier 692
- :TRIGger:TRANsition:SLOPe 693
- :TRIGger:TRANsition:SOURce 694
- :TRIGger:TRANsition:TIME 695
- :TRIGger:TV Commands 696
- :TRIGger:TV:LINE 697
- :TRIGger:TV:MODE 698
- :TRIGger:TV:POLarity 699
- :TRIGger:TV:SOURce 700
- :TRIGger:TV:STANdard 701
- :TRIGger:USB Commands 702
- :TRIGger:USB:SOURce:DMINus 703
- :TRIGger:USB:SOURce:DPLus 704
- :TRIGger:USB:SPEed 705
- :TRIGger:USB:TRIGger 706
- :WAVeform Commands 707
- :WAVeform Commands 29 711
- :WAVeform:BYTeorder 715
- :WAVeform:COUNt 716
- :WAVeform:DATA 717
- :WAVeform:FORMat 719
- :WAVeform:POINts 720
- :WAVeform:POINts:MODE 722
- #Vsteps = 724
- :WAVeform:SEGMented:COUNt 727
- :WAVeform:SEGMented:TTAG 728
- :WAVeform:SOURce 729
- :WAVeform:SOURce:SUBSource 733
- :WAVeform:TYPE 734
- :WAVeform:UNSigned 735
- :WAVeform:VIEW 736
- :WAVeform:XINCrement 737
- :WAVeform:XORigin 738
- :WAVeform:XREFerence 739
- :WAVeform:YINCrement 740
- :WAVeform:YORigin 741
- :WAVeform:YREFerence 742
- :WGEN Commands 743
- :WGEN:FREQuency 745
- :WGEN:FUNCtion 746
- :WGEN:FUNCtion? 747
- <signal><NL> 747
- :WGEN:FUNCtion:PULSe:WIDTh 748
- :WGEN:FUNCtion:RAMP:SYMMetry 749
- :WGEN:FUNCtion:SQUare:DCYCle 750
- :WGEN:OUTPut 751
- :WGEN:OUTPut:LOAD 752
- :WGEN:PERiod 753
- :WGEN:RST 754
- the same as a high- level 755
- :WGEN:VOLTage:HIGH 756
- :WGEN:VOLTage:LOW 757
- :WGEN:VOLTage:OFFSet 758
- :WMEMory<r> Commands 759
- :WMEMory<r>:CLEar 761
- :WMEMory<r>:DISPlay 762
- :WMEMory<r>:LABel 763
- :WMEMory<r>:SAVE 764
- :WMEMory<r>:SKEW 765
- :WMEMory<r>:YOFFset 766
- :WMEMory<r>:YRANge 767
- :WMEMory<r>:YSCale 768
- Commands" on page 860) 769
- Parameters 773
- :CHANnel:ACTivity 774
- :CHANnel:LABel 775
- :CHANnel:THReshold 776
- :CHANnel2:SKEW 777
- :CHANnel<n>:INPut 778
- :CHANnel<n>:PMODe 779
- :DISPlay:CONNect 780
- :DISPlay:ORDer 781
- Command Syntax 782
- :EXTernal:PMODe 783
- :FUNCtion:SOURce 784
- :FUNCtion:VIEW 785
- :HARDcopy:DESTination 786
- :HARDcopy:FILename 787
- :HARDcopy:GRAYscale 788
- :HARDcopy:IGColors 789
- :HARDcopy:PDRiver 790
- :MEASure:LOWer 791
- :MEASure:SCRatch 792
- :MEASure:TDELta 793
- :MEASure:THResholds 794
- :MEASure:TMAX 795
- :MEASure:TMIN 796
- :MEASure:TSTArt 797
- :MEASure:TSTOp 798
- :MEASure:TVOLt 799
- :MEASure:UPPer 801
- :MEASure:VDELta 802
- :MEASure:VSTArt 803
- :MEASure:VSTOp 804
- :MTESt:AMASk:{SAVE 805
- :MTESt:AVERage 806
- :MTESt:AVERage:COUNt 807
- :MTESt:LOAD 808
- :MTESt:RUMode 809
- :MTESt:RUMode:SOFailure 810
- :MTESt:{STARt 811
- :MTESt:TRIGger:SOURce 812
- DISK invalid 814
- PCL invalid 814
- Old Print Option: Is Now: 814
- :SAVE:IMAGe:AREA 815
- <value> ::= LIN 816
- :TIMebase:DELay 817
- :TRIGger:THReshold 818
- :TRIGger:TV:TVMode 819
- Error Messages 821
- Error Messages 33 823
- Status Reporting 829
- From Overload 831
- Event Registers 831
- From Mask Test 831
- Status Byte Register (STB) 833
- Status Reporting 34 835
- Trigger Event Register (TER) 836
- Output Queue 837
- Message Queue 838
- Error Queue 841
- Status Condition Register 843
- Arm Event Register (AER) 844
- Clearing Registers and Queues 847
- Synchronizing Acquisitions 849
- Set Up the Oscilloscope 850
- Acquire a Waveform 850
- Retrieve Results 850
- Blocking Synchronization 851
- Synchronizing Acquisitions 35 853
- Command Classifications 860 859
- Query Return Values 867 859
- Command Classifications 860
- ":DISPLAY:LABEL ON" 861
- Program Message 861
- Instruction Header 861
- Separator 861
- Program Data 861
- Simple Command Headers 863
- Compound Command Headers 863
- Common Command Headers 863
- Program Data Syntax Rules 864
- Duplicate Mnemonics 865
- Query Return Values 867
- Programming Examples 869
- VISA COM Examples 870
- Programming Examples 37 871
- VISA COM Example in C# 879
- VISA Examples 897
- VISA Example in Visual Basic 906
- VISA Example in C# 916
- SICL Examples 938
- SICL Example in Visual Basic 947
- Numerics 959
- , 277, 280 963
- function, 277, 280 965
Manuais e produtos relacionados com Medição, teste e controlo Agilent Technologies InfiniiVision 3000 DSO-X 3054A
(326 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.097 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais