Agilent Technologies 34420A Especificações Página 173
- Página / 294
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Status Reporting Commands
SYSTem:ERRor?
This command queries the meter’s error queue. Up to 20 errors can be
stored in the queue. Errors are retrieved in first-in-first out (
FIFO) order.
Each error string may contain up to 80 characters.
STATus:QUEStionable:CONDition?
This command queries the questionable status condition register. The
meter returns a decimal value which corresponds to the binary-weighted
sum of all bits set in the register.
STATus:QUEStionable:ENABle <
enable value
>
This command enables bits in the Questionable Data enable register. The
selected bits are then reported to the Status Byte.
STATus:QUEStionable:ENABle?
This command queries the Questionable Data enable register. The meter
returns a binary-weighted decimal representing the bits set in the enable
register.
STATus:QUEStionable:EVENt?
This command queries the Questionable Data event register. The meter
returns a decimal value which corresponds to the binary-weighted sum of
all bits set in the register.
STATus:OPERation:CONDition?
This command queries the operational status condition register. The
meter returns a decimal value which corresponds to the binary-weighted
sum of all bits set in the register. Only bit 8 (decimal 256) is used
(indicates the digital filter has settled).
STATus:OPERation:ENABle <
enable value
>
This command enables bits in the Questionable Data enable register. The
selected bits are then reported to the Status Byte.
STATus:OPERation:ENABle?
This command queries the Questionable Data enable register. The meter
returns a binary-weighted decimal representing the bits set in the enable
register.
4
Chapter 4 Remote Interface Reference
Status Reporting Commands
171
- Agilent 34420A 3
- The Front-Panel at a Glance 4
- Display Annunciators 6
- The Rear Panel at a Glance 7
- In This Book 8
- Contents 12
- Quick Start 13
- To Prepare the Meter For Use 15
- If the Meter Does Not Turn On 16
- 250 mAT fuse 17
- To Adjust the Carrying Handle 18
- To Make Input Connections 19
- Earth Ground (shell) 20
- To Measure Voltage 21
- To Measure Resistance 22
- EXTERNAL 24
- FIXED VALUE 24
- INTERNAL 24
- To Select a Range 25
- To Set the Number of Digits 26
- To Set the Integration Time 27
- Front-Panel Display Formats 28
- To Rack Mount the Meter 29
- Front-Panel Operation 31
- Front-Panel Menu Reference 33
- Ø6:CAL COUNT Ø 7:MESSAGE 34
- A Front-Panel Menu Tutorial 35
- On/Off 37
- A: , B: , etc.) 37
- 1: , 2: , etc.) 38
- Recall 39
- On/Off 40
- NULL VALUE parameter 41
- Null 42
- To Select an Input Channel 43
- < or > 48
- To Trigger the Meter 49
- * (sample) annunciator is on 49
- To Use Reading Hold 50
- (Ch 1 voltage − Ch 1 Null ) 51
- To Use Reading Memory 52
- Features and Functions 55
- Input Filters 57
- Ø ANALOG Ø ANA + DIG 57
- Enter to enable the 58
- Integration Time 60
- Reducing Measurement Noise 62
- Number of Digits Displayed 64
- Sets the 10 Volt DC range 66
- Sets the 1 mV DC range 66
- Sets auto ranging on 66
- 2-wire resistance 66
- Overload Detection 67
- Input Channels 68
- − Ch 1 Null ) 69
- Measurement Units 73
- RTD Measurements 74
- Thermistor Measurements 74
- Thermocouple Measurements 75
- Math Operations 76
- Null (Relative) Operation 79
- Reading Hold 81
- Trigger Source Choices 84
- ‘Trig’ annunciator turns on 85
- Number of Samples 88
- Number of Triggers 88
- Trigger Delay 89
- ∨ until 90
- Enter 90
- Automatic Trigger Delays 91
- System-Related Operations 92
- Error Conditions 94
- Self-Test 95
- Display Control 96
- Comma Separators 97
- Firmware Revision Query 97
- SCPI Language Version 98
- Voltmeter Complete Terminal 99
- External Trigger Terminal 99
- chart output voltage 100
- = 0.001 100
- Chart Rollover 102
- Remote Interface Selection 103
- HP-IB Address 104
- Parity Selection (RS-232) 106
- Calibration 109
- Calibration Count 112
- Calibration Message 113
- or MEASure commands 114
- are enabled 116
- 100 mV ranges 116
- Remote Interface Reference 117
- Command Summary 119
- Status Reporting Commands 125
- Calibration Commands 126
- Remote Interface Commands 126
- IEEE-488.2 Common Commands 127
- <function> 129
- Using the MEASure? Command 130
- Using the CONFigure Command 130
- Using the READ? Command 132
- Selecting the Input Channel 142
- Null (Relative) Commands 147
- Input Filter Commands 148
- Math Operation Commands 150
- Scale operation commands 152
- First time SCPI users 153
- Triggering 154
- The Wait-for-Trigger State 155
- Triggering Commands 156
- System-Related Commands 159
- The SCPI Status Model 161
- SCPI Status System 162
- The Status Byte 163
- IEEE-488 bus 165
- IEEE-488 SRQ interrupt 165
- The Standard Event Register 167
- *PSC {0 175
- *SRE <enable value> 175
- CALibration:STRing? 177
- CALibration:VALue? 177
- RS-232 Configuration Overview 178
- RS-232 Data Frame Format 179
- Connection to a Printer 181
- DTR / DSR Handshake Protocol 181
- RS-232 Troubleshooting 183
- RS-232 Interface Commands 184
- SCPI) defines how 185
- IEEE-488.2 interface 186
- SCPI Data Types 187
- Input Message Terminators 188
- Output Data Formats 188
- TALK ONLY for Printers 189
- To Set the HP-IB Address 190
- To Set the Baud Rate 192
- To Set the Parity 193
- (Keithley 181) 194
- Specific Issues 195
- SCPI Compliance Information 196
- Messages 200
- Error Messages 201
- Execution Errors 202
- SEC is not a valid suffix) 203
- BUS and a READ? 204
- INTERRUPTED 206
- UNTERMINATED 206
- DEADLOCKED 206
- Self-Test Errors 209
- Calibration Errors 211
- Application 213
- Programs 213
- Application Programs 214
- HP BASIC Language Programs 215
- ... continued 217
- Agilent Control Libraries 224
- C Language Programs 231
- C / HP-IB Example 1 233
- C / HP-IB Example 2 235
- C / HP-IB Program Example 3 239
- Microsoft Excel Macro Example 243
- Macro Comments 244
- Measurement Tutorial 247
- Voltage Measurements 249
- Resistance Measurements 258
- ) − V 259
- 1 mA 10 mV 20, 100, or 500 mV 261
- Temperature Measurements 263
- Ice Bath 266
- N/A = Not Available 269
- Input Connector 272
- Part NumberDescription 273
- Specifications 274
- Chapter 8 Specifications 275
- MEASUREMENT CHARACTERISTICS 276
- OPERATING CHARACTERISTICS 277
- Dimensions 279
- Sensitivity 284
- Resolution 285
- Accuracy 285
- 24-Hour Accuracy 286
- 90-Day and 1-Year Accuracy 286
- Temperature Coefficients 286
- DECLARATION OF CONFORMITY 293
Manuais e produtos relacionados com Multímetros Agilent Technologies 34420A
(22 páginas)
(133 páginas)
Multímetros Agilent Technologies 8487D Especificações
(144 páginas)
(144 páginas)
Multímetros Agilent Technologies 22D Especificações
(118 páginas)
(118 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais