Agilent Technologies 8753ES Guia do Utilizador Página 275
- Página / 487
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
4-51
Printing, Plotting, and Saving Measurement Results
Formatting a Disk
Formatting a Disk
1. Press .
2. Choose the type of format you want:
❏
❏
3. Press .
Solving Problems with Saving or Recalling Files
If you encounter a problem when you are storing files to disk, or the analyzer internal
memory, check the following list for possible causes:
• Look in the analyzer display message area. The analyzer may show a message that will
identify the problem. Refer to the "Error Messages" chapter of the reference guide if you
view a message.
• Make sure that you are NOT using a single-sided floppy disk in the analyzer disk drive.
• Make sure that you are using a formatted disk.
• Make sure that the disk has not been formatted with the LIF-HFS (hierarchical file
system) extensions as the analyzer does not support this format.
If You Are Using an External Disk Drive
• Make sure that the analyzer is in system controller mode, by pressing
.
• Make sure that you have connected the disk drive to ac power, switched on the power,
and connected a GPIB cable between the disk drive and the analyzer.
• Make sure that the analyzer recognizes the disk drive's GPIB address, as explained in
"If You Are Plotting Measurement Results to a Disk Drive" on page 4-11.
• Make sure that the analyzer recognizes the disk (drive) unit that you selected (0 or 1).
• If the external disk is a hard disk, make sure that the disk volume number is set
correctly.
• If the disk drive is an older HP 9122, it may not recognize the newer high density disks.
• Substitute the GPIB cable.
• Substitute the disk drive.
Save/Recall
FILE UTILITIES
FORMAT DISK
FORMAT:LIF
FORMAT:DOS
FORMAT EXT DISK
YES
Local
SYSTEM CONTROLLER
CNTROLLER
- User’s Guide 1
- Certification 2
- Assistance 2
- Safety Notes 3
- How to Use This Guide 3
- Documentation Map 4
- Contents 10
- Making a Basic Measurement 18
- Using Display Functions 24
- AUX CHAN 29
- Blanking the Display 35
- Using Markers 38
- To Activate Display Markers 39
- To Use Delta (∆) Markers 42
- To Activate a Fixed Marker 43
- To Use Polar Format Markers 46
- To Use Smith Chart Markers 48
- Marker Fctn 49
- MARKER→START 49
- Setting the CW Frequency 53
- Measuring Electrical Length 58
- Measuring Phase Distortion 60
- SMOOTHING APERTURE 63
- Definitions 64
- Measuring Amplifiers 68
- COUPLED PWR ON off 72
- Measuring Gain Compression 74
- (ES Analyzers Only) 78
- Calibrate and Measure 88
- (Power: 0 dBm/IF BW: 3700 Hz) 89
- Using Linear Sweep 89
- Using Swept List Mode 89
- Creating Flat Limit Lines 91
- Creating Single Point Limits 95
- Editing Limit Segments 96
- Running a Limit Test 96
- Offsetting Limit Lines 97
- Editing Ripple Test Limits 102
- Running the Ripple Test 104
- Making Measurements 105
- RIPL LIMIT on OFF 105
- RIPL VALUE BAND 107
- RIPL VALUE [ABSOLUTE ] 107
- RIPL VALUE [MARGIN ] 108
- Setting Up Bandwidth Limits 109
- Running a Bandwidth Test 111
- BW MARKER on OFF 112
- BW DISPLAY on OFF 113
- Using Test Sequencing 115
- Running a Sequence 117
- Stopping a Sequence 117
- Editing a Sequence 117
- Changing the Sequence Title 119
- Storing a Sequence on a Disk 120
- Loading a Sequence from Disk 121
- Purging a Sequence from Disk 121
- Printing a Sequence 121
- IF LOOP COUNTER = 0 129
- IF LOOP COUNTER <> 0 129
- Limit Test Example Sequence 134
- (Option 014 Only) 136
- GPIB Commands 138
- 2 Making Mixer Measurements 139
- Using This Chapter 140
- Making Mixer Measurements 141
- Measurement Considerations 142
- How RF and IF Are Defined 145
- in power: 149
- Power Meter Calibration 150
- FREQS OFFS ON 156
- Scale Ref 157
- AUTOSCALE 157
- Measurement 162
- Fixed IF Mixer Measurements 164
- Sequence 2 Setup 169
- Phase Measurements 172
- Amplitude and Phase Tracking 176
- LO to RF Isolation 182
- RF Feedthrough 184
- SWR / Return Loss 187
- Velocity Factor 198
- --------= 198
- Time Domain Bandpass Mode 200
- Time Domain Low Pass Mode 203
- the CW frequency. For 211
- Masking 214
- Windowing 215
- Circuit (Real Format) 217
- Resolution 220
- Range Resolution 222
- Setting the Gate 223
- Selecting Gate Shape 224
- Measurement Results 225
- Configuring a Print Function 228
- Defining a Print Function 230
- Configuring a Plot Function 233
- Defining a Plot Function 237
- Selecting Line Types 239
- Choosing Scale 239
- Choosing Plot Speed 240
- Plotter 242
- To View Plot Files on a PC 244
- Using Ami Pro 245
- Using Freelance 245
- Printer 247
- Save/Recall 253
- Parameters 256
- SYSTEM CONTROLLER 257
- Places Where You Can Save 258
- Saving an Instrument State 260
- Saving Measurement Results 261
- ASCII Data Formats 263
- #HZSDBR50 265
- Saving in Textual (CSV) Form 266
- Instrument State Files 268
- Deleting a File 273
- Renaming a File 274
- Recalling a File 274
- Formatting a Disk 275
- Interconnecting Cables 280
- Connector Repeatability 280
- Temperature Drift 281
- Frequency Drift 281
- Performance Verification 281
- Devices 283
- Increasing Sweep Speed 285
- To Set the Sweep Type 287
- To Activate Chop Sweep Mode 288
- To Use External Calibration 288
- Increasing Dynamic Range 290
- Reducing Noise 291
- Reducing Receiver Crosstalk 294
- Reducing Recall Time 294
- 6 Calibrating for Increased 295
- How to Use This Chapter 296
- Introduction 297
- Calibration Considerations 298
- Saving Calibration Data 299
- Restarting a Calibration 299
- The Calibration Standards 299
- Fringe Capacitance 301
- Types of Error Correction 304
- Receiver Calibration 309
- Measurements 311
- DONE: 1-PORT CAL 322
- DONE 2-PORT CAL 326
- Matched Adapters 339
- Fixtures 342
- TRL Error Correction 344
- LRM Error Correction 348
- DONE TRL/LRM 351
- Set Up the Measurement 352
- Connect the ECal Equipment 353
- Select the ECal Options 354
- Perform the Calibration 356
- CONTINUE ECal 357
- Perform the Confidence Check 359
- Remove the Adapter 368
- Verify the Results 369
- 7 Operating Concepts 371
- System Operation 373
- The Built-In Test Set 374
- The Receiver Block 374
- The Microprocessor 375
- Processing 376
- Processing Details 377
- Operating Concepts 378
- Processing 378
- COUPLED CH OFF 378
- Output Power 380
- Power Coupling Options 381
- Sweep Time 382
- Channel Stimulus Coupling 385
- Sweep Types 386
- Power Sweep (dBm) 390
- CW Time Sweep (Seconds) 390
- Selecting Sweep Modes 390
- S-Parameters 391
- The S-Parameter Menu 393
- Analyzer Display Formats 395
- Phase Format 396
- Group Delay Format 397
- Smith Chart Format 398
- Polar Format 399
- Linear Magnitude Format 400
- SWR Format 401
- Real Format 401
- Imaginary Format 402
- Group Delay Principles 402
- SMOOTHING APERTURE 404
- Electrical Delay 405
- Noise Reduction Techniques 406
- Smoothing 407
- IF Bandwidth Reduction 407
- Measurement Calibration 409
- RESUME CAL SEQUENCE 420
- Calibration Routines 426
- Modifying Calibration Kits 428
- Procedure 429
- Modify Calibration Kit Menu 429
- Verify Performance 436
- Selection Menu 437
- Why Use TRL Calibration? 438
- TRL Terminology 439
- Calibration 442
- OFFSET Z0 444
- SET REF: THRU 448
- GPIB Operation 449
- GPIB STATUS Indicators 450
- System Controller Mode 450
- Talker/Listener Mode 450
- Pass Control Mode 450
- Address Menu 450
- Using the Parallel Port 451
- Limit Line Operation 452
- Edit Limits Menu 453
- Edit Segment Menu 453
- Offset Limits Menu 453
- Knowing the Instrument Modes 454
- Tuned Receiver Mode 456
- Frequency Offset Operation 457
- 8753E 8753ES 461
- General Information 466
- Table 8-1 Contacting Agilent 467
- Asia Call Center Numbers 467
- Safety Symbols 468
- Instrument Markings 468
- Safety Considerations 469
- Servicing 470
- General 471
- Declaration of Conformity 473
- Index-2 476
- Index-4 478
- Index-6 480
- Index-8 482
- Index-10 484
- Index-11 485
- Index-12 486
- Index-13 487
Manuais e produtos relacionados com Redes Agilent Technologies 8753ES
Redes Agilent Technologies DP111 Especificações
(452 páginas)
(452 páginas)
Redes Agilent Technologies 8510C Especificações
(22 páginas)
(22 páginas)
Redes Agilent Technologies 81680A Guia do Utilizador
(60 páginas)
(60 páginas)
Redes Agilent Technologies N9360A Manual do Utilizador
(376 páginas)
(376 páginas)
Redes Agilent Technologies 8753ET Especificações
(262 páginas)
(262 páginas)
Redes Agilent Technologies 8753ET Guia do Utilizador
(546 páginas)
(546 páginas)
(21 páginas)
Redes Agilent Technologies 8753ES Guia do Utilizador
(245 páginas)
(245 páginas)
Redes Agilent Technologies N9360A Manual do Utilizador
(354 páginas)
(354 páginas)
Redes Agilent Technologies 81640A Guia do Utilizador
(114 páginas)
(114 páginas)
Redes Agilent Technologies E6474A Manual de Serviço
(52 páginas)
(52 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.166 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais