Agilent Technologies E7495A RF Manual de Serviço Página 31
- Página / 686
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 1 31
Getting Started
Unpacking the E7495A/B Test Set
Getting Started
Option 813 W-CDMA antenna and pre-selector filter,
includes:
• W-CDMA antenna 2.1-2.17 GHz
(pn E6455-80003)
• preselector filter (pn 0955-1667)
• RF TNC to N connector (pn 1200-1897) for
Option 210 - cdmaOne / CDMA 2000 Over
Air Test
Option 820 External charger/battery pack/DC adapter,
includes:
• Battery 10.8V 6A-HR LI-ION
(pn 1420-0883)
• External power supply AC/DC adapter
24 VDC 100 W (pn 0950-4404)
• DC car adapter DC to DC adaptor output
19 VDC 70 W (pn 0950-4412)
• dual battery charger, 12 V AT 1 A
(pn 0950-4276)
Option
N8482A
Power Sensor, 100 kHz to 4.2 GHz:
Option 840 Hard transit case (pn E7495-80016)
Option 900 UK power cord
Option 901 AUS/NZ/CH power cord
Option 902 Euro power cord
Option 903 US power cord
Option 906 Swiss power cord
Option 912 Denmark power cord
Option 917 So Af/India power cord
Option 918 Japan power cord
Option
Number
Description (as printed
on the analyzer rear
panel)
Detailed Description
- Measurement Guide 1
- Technology Licenses 2
- Restricted Rights Legend 2
- Contents 10
- 1 Getting Started 19
- Introduction 20
- Getting Started 21
- Test set options 28
- 34 Chapter 1 34
- Install a Battery 37
- Using the Backpack 41
- 42 Chapter 1 42
- More Information from Agilent 43
- 44 Chapter 1 44
- 2 One Port Insertion Loss 45
- One Port Insertion Loss 46
- 58 Chapter 2 58
- • Non Idle Power 61
- Chan or 63
- GPS time reference, you will 68
- Measurements 69
- 76 Chapter 3 76
- Setting Measurement Offset 84
- Setting the CDP Type 85
- Off. It 89
- Restart key 89
- ASS” or 93
- On and enter the RF 102
- Analyzer Measurement 104
- Non Idle Power 105
- Measurement Results 109
- the target cell is too far 110
- Customizing Your Display 114
- Codogram Display 120
- 4 Two Port Insertion Loss 123
- Two Port Insertion Loss 124
- To Set Sweep: 127
- To Set Averaging: 128
- Single sweep mode 129
- To restart averaging: 129
- Adding a Marker 130
- Chapter 4 133 133
- Meter Only) 134
- Frequency 135
- Normal 136
- Clearing Normalization 137
- Setting Source Level 137
- 138 Chapter 4 138
- Step Notes 138
- Optimizing Dynamic Range 139
- Setting the Pass/Fail Limits 140
- 5 Adjacent Channel Power 141
- Adjacent Channel Power 142
- On. Each time you 148
- On or Off) changes 148
- Signals) 152
- Setting the Control Units 152
- Setting the Range Control 153
- Setting Noise Correction 154
- 160 Chapter 5 160
- (ACLR) Measurements 161
- 6 Working with Batteries 163
- Installing Batteries 164
- Viewing Battery Status 165
- Working with Batteries 166
- Charging Batteries 168
- Reconditioning Batteries 170
- Push to 172
- Recalibrate Left Battery Bay 172
- Battery Care 173
- Battery Specifications 176
- 180 Chapter 6 180
- 7 CDMA Analyzer 181
- Using the CDMA Analyzer 182
- CDMA Analyzer 184
- Manual 184
- Interpreting the Display 187
- Setting the PN Offset 191
- Setting the PN Increment 191
- PN Inc text on the 192
- Setting Units 193
- measurements by the test 194
- Setting Measurement Time 195
- Setting Quick Page Channel 196
- On or Off 201
- 4 Set the upper limit 202
- 7[Mod Format] 210
- On (with the 42.51 dB loss 211
- Measurement 212
- 218 Chapter 7 218
- 8 CDMA Over Air 219
- Using the CDMA Over Air Tool 220
- CDMA Over Air 221
- GPS is selected. If 223
- 230 Chapter 8 230
- Auto or Manual 234
- 5 Set the upper limit 242
- 9 Channel Scanner 261
- Using the Channel Scanner 262
- Channel Scanner 263
- List, and then select the 269
- Cust. Then select the 269
- Displaying Frequency or Power 274
- 10 Distance to Fault 277
- Measuring Distance to Fault 278
- (Manual Frequency Range) 283
- Distance to Fault 284
- RG, BTS 284
- RG or BTS, you will 284
- Cust), you must 285
- (Automatic Frequency Range) 286
- Meters or Feet 287
- Cust (Custom Cable). Proceed 288
- Frequency Range of 289
- Clearing Calibration 290
- Return Loss and the One 291
- Port Insertion Loss 291
- On, the position and the 292
- 11 E1 Analyzer 299
- Making E1 Measurements 300
- E1 Analyzer 301
- Control Button Selections 303
- DSX Service panel Test Set 305
- Sample Monitor Full E1 Test 308
- Rx Tx 309
- Setting Up Delay Test Mode 312
- Turning On Sound 314
- Setting Up E1 Diagnostics 315
- Patterns 316
- Status Indicators 320
- Testing and Fault Mitigation 321
- 324 Chapter 11 324
- Terminology 325
- 12 GSM and EDGE Analyzer 327
- GSM and EDGE Analyzer 328
- Range, Auto, or List 331
- Range or 331
- Auto, go to step 8 331
- List, go to 331
- Auto, you may set Start and 332
- List, you may 332
- ]) in the selected 337
- Settings 339
- Setting your Scan Mode 340
- Setting the Channel Standard 346
- Setting Autoscale 347
- Setting the Reference Level 348
- Setting Scale/Division 348
- Setting the Display Position 349
- Setting Auto Order 350
- Setting Bar Top and Units 350
- Setting Mid-Bar 351
- Setting Zoom 351
- Setting Zoom Offset 352
- Setting Zoom Interval 353
- Setting PvT Mask 354
- Setting Auto Mode Bar Count 354
- Setting Slot Synchronization 355
- Setting TS# (w/ BCCH) 356
- 3 [Limits] 361
- 372 Chapter 12 372
- RMS and Peak Phase Error 374
- 13 Power Meter 379
- Power Meter 380
- 388 Chapter 13 388
- 14 Return Loss 389
- Measuring Return Loss 390
- Return Loss 391
- 15 Signal Generator 401
- Using the Signal Generator 402
- Signal Generator 403
- Using the RF OUT Loss field 410
- Persistent Signal Generator 411
- 16 Spectrum Analyzer 413
- Using the Spectrum Analyzer 414
- Spectrum Analyzer 415
- Freq (frequency) 415
- Chan (channel number) 415
- Setting the Analyzer Detector 420
- Adding or Removing a Marker 426
- Chapter 16 429 429
- Spectrogram Display 435
- On and Off 437
- On, the SEM mask 455
- WCDMA UTRA signals only: The 455
- 458 Chapter 16 458
- 17 Basic System Operations 459
- Basic System Operations 460
- System Reference Introduction 461
- Setting System References 462
- Setting up the DC Bias Option 463
- Printing a Screen to a File 465
- File Naming Options 466
- Select 467
- Saving Data 469
- Managing Media Types 473
- Saving the State 478
- Saving the Power-Up State 478
- Recalling the State 479
- Deleting States 480
- Viewing System Statistics 481
- Viewing Battery Statistics 482
- Using the Option Manager 483
- Installing an Option 484
- Testing System Functions 485
- 486 Chapter 17 486
- 18 T1 Analyzer 487
- Making T1 Measurements 488
- T1 Analyzer 489
- Internal 490
- Sample Monitor Full T1 Test 503
- Sample Emulate CSU/NIU Test 507
- Sample Delay Test 512
- Turning on sound 514
- Setting up T1 diagnostics 515
- Status indicators 519
- Measurement results fields 519
- 528 Chapter 18 528
- Analyzer 535
- Selecting a Reference 537
- RF Connections 538
- Analyzer Measurements 539
- Transmitter Measurement 540
- Multiple-View Display 542
- On 10% of the time 543
- NOTE: You can have QPSK 544
- 546 Chapter 19 546
- Setting the Display Options 548
- Chapter 19 555 555
- Measurement Settings 556
- Attenuators, and Preamps 558
- Enabling PICH and S-CCPCH 564
- Setting the EVM Mode 565
- Setting the IF Equalizer 565
- HSDPA) Analyzer 568
- Δ power metrics are: 570
- 574 Chapter 19 574
- Over Air 575
- Off to remove the location 582
- On 10% of the 585
- 590 Chapter 20 590
- Setting the Scrambling Codes 596
- Slow, Medium, or Fast 602
- Setting the PICH Parameters 604
- HSDPA) Over Air Measurement 608
- Chapter 20 615 615
- 616 Chapter 20 616
- Specifications 617
- Safety considerations 618
- Lifting and Handling 620
- Product Markings 622
- Chapter 21 623 623
- 624 Chapter 21 624
- Chapter 21 625 625
- 626 Chapter 21 626
- Chapter 21 627 627
- 628 Chapter 21 628
- Certification 629
- Manufacturer’s Declaration 629
- 630 Chapter 21 630
- Chapter 21 631 631
- Disposal of Batteries 632
- ≤ ± 0.03 ppm 633
- ± –100 dBm 639
- 646 Chapter 21 646
- 22 Connector Care 647
- Repeatability 648
- RF Cable and Connector Care 648
- Proper Connector Torque 649
- Connector Wear and Damage 650
- Cleaning Procedure 650
- Test Set 652
- Warranty 653
- 24 Glossary 657
- Glossary 658
- Copyright Information 661
- 676 Chapter 25 676
- Index 677 677
- 678 Index 678
- Index 679 679
- 680 Index 680
- Index 681 681
- 682 Index 682
- Index 683 683
- 684 Index 684
- Index 685 685
- 686 Index 686
Manuais e produtos relacionados com Multímetros Agilent Technologies E7495A RF
(42 páginas)
(62 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais