Agilent Technologies 53150A Manual de Instruções Página 143
- Página / 174
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 4 Command Reference
Common Commands
Programming Guide 4-47
4
*ESR? (Event Status Register Query)
COMMAND *ESR?
Queries the Standard Event Status Register, shown in Figure 4-4.
This event register captures changes in conditions, by having each event
bit correspond to a specific condition in the instrument. An event becomes
TRUE when the associated condition makes the defined transition. The
event bits, once set, are “sticky”—i.e., they cannot be cleared until they are
read, even if they do not reflect the current status of a related condition.
This register is cleared by *CLS, by *ESR?, and at power-on. Note that the
instrument's power-on sequence initially clears the register, but then
records any subsequent events during the power-on sequence including
setting the PON (power on) bit.
Figure 4-4. Standard Event Status Register
See the section titled “Standard Event Status Register” on Page 3-30 of
this guide for a detailed description of the Standard Event Status
Register.
QUERY RESPONSE • Numeric data transferred as ASCII bytes in <NR1> format.
• Range is 0 to 255.
• The query response is an integer formed by the binary-weighting of the
bits. The value of any unused bit is zero.
(
1
)
Operation Complete
Not Used
(
4
)
Query Error
2
(
8
)
Device Dependent Error
3
(
16
)
Execution Error
4
(
32
)
Command Error
5
Not Used
6
(
128
)
Power On
7
Bits
0
1
- Programming Guide 1
- Contents 3
- 4 Command Reference 5
- 5 Errors 6
- Before You Start 7
- Getting Started 9
- How to Use This Guide 9
- New Users 10
- Experienced Programmers 11
- Applications 11
- Programming Guide Contents 12
- Assumptions 13
- Related Documentation 14
- 1-10 Programming Guide 16
- Command Summary 17
- Chapter 2 Command Summary 20
- 2-4 Programming Guide 20
- (Part 1 of 2) 20
- 2-6 Programming Guide 22
- SCPI Conformance Information 24
- IEEE 488.2 Common Commands 25
- 2-10 Programming Guide 26
- Programming Guide 2-11 27
- Std/New Column 28
- Parameter Form Column 28
- Programming Guide 2-13 29
- 2-14 Programming Guide 30
- Programming Guide 2-15 31
- 2-16 Programming Guide 32
- Programming Guide 2-17 33
- 2-18 Programming Guide 34
- *RST Response 35
- 2-20 Programming Guide 36
- Programming Your Counter 37
- Chapter Summary 39
- Programming Examples 40
- To Connect With the GPIB 41
- Making an RS-232 Cable 43
- (Female) 44
- Remote/Local Operation 47
- Common Command Format 48
- SCPI Command and Query Format 48
- Elements of SCPI Commands 49
- Abbreviated Commands 50
- Keyword Separator 50
- Optional Keyword 50
- :SENS:FREQ:RES 51
- :FREQ:RES 51
- Parameter Types 52
- Parameter Separator 53
- Query Parameters 53
- Suffixes 53
- Command Terminator 54
- Using Multiple Commands 55
- :SENS:AVER:COUN 5 56
- :SENS:AVER:STAT ON 56
- Response Messages 57
- Response Message Syntax 57
- <new line> 58
- Response Message Data Types 59
- 3-24 Programming Guide 60
- Status Reporting 61
- 3-26 Programming Guide 62
- Status Byte Register and 63
- RQS /MSS 63
- Condition Register 70
- Transition Filter 70
- Event Register 71
- Event Enable Register 72
- Programming the Counter for 77
- Event Status Register 78
- Computer When Measuring has 79
- Completed—Example 3 79
- 3-44 Programming Guide 80
- Programming Guide 3-45 81
- FREQ:OFFS:STAT ON 83
- Programming the Counter to 84
- Synchronize Measurements 84
- Using the *WAI Command 85
- Using the *OPC? Command 85
- Writing SCPI Programs 88
- Programming Guide 3-53 89
- 3-56 Programming Guide 92
- Programming Guide 3-57 93
- 3-58 Programming Guide 94
- Programming Guide 3-59 95
- 3-60 Programming Guide 96
- Command Reference 97
- COMMAND :ABORt 100
- FRONT-PANEL 100
- :DISPlay Subsystem 101
- COMMAND GET 103
- COMMENTS • *RST: OFF 104
- :INPut Subsystem 105
- :MEASure Subsystem 106
- Command Description 107
- COMMAND :CONFigure? 108
- FUNCTION 112
- DESCRIPTION 112
- Using :MEAsure 114
- Using :CONFigure with :READ? 115
- :MEMory Subsystem 116
- [:SENSe] Subsystem 118
- [:SENSe]:FUNCtion Subtree 123
- [:SENSe]:POWer Subtree 125
- [:SENSe]:ROSCillator Subtree 126
- :STATus Subsystem 127
- COMMAND :STATus:PRESet 131
- :STATus:QUEStionable Subtree 132
- :SYSTem Subsystem 135
- :TRIGger Subsystem 138
- COMMAND *CLS 139
- *DDT <arbitrary block> 140
- (Define Device Trigger Query) 140
- COMMAND *ESR? 143
- *IDN? (Identification Query) 144
- *IST? (Instrument Status) 144
- *RCL (Recall Command) 146
- COMMAND *RST 147
- *SAV (Save Command) 148
- <NRF> RANGE • 0 to 255 149
- <NRF> RESOLUTION 1 149
- COMMAND *STB? 151
- COMMAND *TRG 152
- *TST? (Self-Test Query) 153
- Introduction 156
- Reading an Error 156
- Error Queue 157
- Error Types 158
- Command Error 159
- Execution Error 159
- Query Error 160
- Error List 160
- Chapter 5 Errors 161
- Programming Guide 5-7 161
- Table 5-2. Errors 161
- 5-8 Programming Guide 162
- Table 5-2. Errors (Continued) 162
- Programming Guide 5-9 163
- 5-10 Programming Guide 164
- Programming Guide Index-1 165
- Index-2 Programming Guide 166
- Programming Guide Index-3 167
- Index-4 Programming Guide 168
- Programming Guide Index-5 169
- Index-6 Programming Guide 170
- Programming Guide Index-7 171
- Index-8 Programming Guide 172
- 1-800-800-5281 173
Manuais e produtos relacionados com Multímetros Agilent Technologies 53150A
Multímetros Agilent Technologies 34401A Especificações
(482 páginas)
(482 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.153 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais