Agilent Technologies Agilent G1369B Manual do Utilizador Página 135
- Página / 206
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Agilent 1260 Infinity High Performance Autosampler User Manual 135
Maintenance
9
Removing the Metering Seal
Removing the Metering Seal
When When poor injection volume reproducibility or when metering device / analytical head is leaking.
Tools required p/n Description
8710-0510 Wrench open 1/4 — 5/16 inch
8710-2392 4 mm Hex key
G4226-43800 Seal insert tool
Parts required # p/n Description
1 5063-6589 Metering seal (pack of 2) for 100 µL analytical head
1 In the user interface start the maintenance mode and
select Change metering device function. In the Agilent
Lab Advisor software the Change metering device
function can be found in the Tools section.
2 Open the front door.
- Agilent 1260 Infinity 1
- High Performance 1
- Autosampler 1
- In This Guide 3
- Contents 5
- Features 10
- Overview of the Module 11
- 1 Introduction 12
- Autosampler Principle 13
- Injection Sequence 14
- System Overview 19
- Agilent Technologies 23
- Site Requirements 24
- Power Cords 25
- Bench Space 26
- Condensation 26
- Physical Specifications 27
- Specifications 28
- Installing the Autosampler 31
- Unpacking the Autosampler 32
- Delivery Checklist 33
- 3 Installing the Autosampler 34
- One Stack Configuration 36
- Two Stack Configuration 38
- Using the Module 47
- Leak and Waste Handling 48
- Preparing the Autosampler 49
- 4 Using the Module 50
- & 53
- ' 53
- Control Settings 55
- Method Parameter Settings 56
- Module Configuration 60
- (G4208A) 61
- Optimizing Performance 65
- Delay Volume 66
- 5 Optimizing Performance 68
- Status Indicators 80
- Error Messages 80
- Module Status Indicator 82
- User Interfaces 83
- Agilent Lab Advisor Software 84
- Error Information 85
- 7 Error Information 86
- What are Error Messages 87
- General Error Messages 88
- Remote Timeout 89
- Lost CAN Partner 89
- Leak Sensor Open 90
- Leak Sensor Short 91
- Compensation Sensor Open 91
- Compensation Sensor Short 92
- Fan Failed 92
- Module Error Messages 93
- Side Door Error 94
- Valve to Bypass Failed 95
- Valve to Mainpass Failed 95
- Needle Lock Failed 96
- Needle Carrier Failed 97
- Initialization Failed 99
- Metering Home Failed 100
- Motor Temperature 101
- Invalid Vial Position 102
- Peristaltic Pump Error 103
- Vessel or Wash Vessel Error 103
- Vessel Stuck to Needle 104
- Rear Blind Seat Missing 104
- Test Functions 105
- Introduction 106
- System Pressure Test 107
- 8 Test Functions 108
- Maintenance Positions 112
- Change Needle 113
- Change Loop Capillary 113
- Arm Position 114
- Change Needle Carrier 114
- Change Metering Device 115
- Injector Steps 116
- Step Commands 117
- Maintenance 119
- Introduction to Maintenance 120
- Warnings and Cautions 121
- Overview of Maintenance 122
- Cleaning the module 123
- Removing the needle assembly 124
- 9 Maintenance 126
- Exchanging the Needle Seat 130
- Replacing the Rotor seal 132
- Removing the Metering Seal 135
- >chZgiidda 137
- Tools required Description 143
- Flat head screwdriver 143
- Parts required # Description 143
- 1 Interface board 143
- Replacing the Module Firmware 144
- Parts for Maintenance 145
- 10 Parts for Maintenance 146
- Vial Trays 147
- Recommended Vial Plates 149
- Accessory Kit 150
- Injection Ugrade Kit 150
- Analytical Head Assembly 151
- Injection Valve Assembly 152
- Cover Parts 153
- Leak System Parts 154
- Identifying Cables 155
- Cable Overview 156
- Analog Cables 158
- Remote Cables 160
- 11 Identifying Cables 162
- BCD Cables 163
- CAN/LAN Cables 165
- External Contact Cable 166
- Agilent Module to PC 167
- Hardware Information 169
- Firmware Description 170
- GZh^YZciHnhiZb 171
- BV^c;LjeYViZ 171
- BV^cHnhiZb 171
- GZh^YZci;LJeYViZ 171
- 12 Hardware Information 172
- Obstruction of transport unit 173
- Electrical Connections 174
- Rear view of the module 175
- Interfaces 176
- Overview Interfaces 179
- >chigjbZci 180
- BVaZ ;ZbVaZ ;ZbVaZ BVaZ 180
- APG Remote 181
- Special Interfaces 182
- Special Settings 186
- Instrument Layout 187
- Early Maintenance Feedback 188
- LAN Configuration 189
- 13 LAN Configuration 190
- Connecting the module via LAN 191
- Appendix 193
- General Safety Information 194
- Operation 195
- Safety Symbols 196
- Lithium Batteries Information 197
- (2002/96/EC) 198
- Radio Interference 199
- Sound Emission 200
- Use of Solvents 201
- 14 Appendix 202
- *G1367-90014* 206
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.086 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais