Agilent Technologies U3606B Guia do Utilizador Página 105
- Página / 205
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
DC Power Supply Operation 3
Protection Functions
U3606B User’s Guide 89
This will disable the U3606B output, cause the CC
annunciator to flash, and the OV and Error annunciator to
illuminate.
The “triP” message appears on the display after a few
seconds of inactivity.
Resetting the OVP condition
Use one of the following methods to reset the OVP circuit
after it activates. If the condition that caused the
over- voltage shutdown is still present, the OVP circuit will
turn the output off again.
• When the OVP circuit trips, the U3606B will immediately
prompt you to change the OVP trip level. Use the arrow
keys to select a higher OVP trip level and press [Shift] >
[Save] or [Protect] to save the changes.
• Alternatively, press [Shift] > [Exit] to exit the edit mode
without changing the OVP trip level.
• You may read and clear the error message by accessing
the Utility menu.
If the OVP continues to trip, try lowering the regulated
output current, or raising the OVP trip level.
NOTE
Error number 510, “Voltage output over protection” will be recorded in the
error queue when the OVP circuit trips. Enter the Utility menu to read and
clear the error message.
U3606-90054_UG_EN.book Page 89 Friday, July 11, 2014 5:12 PM
- Agilent U3606B 1
- Multimeter 1
- Safety Symbols 3
- Safety Considerations 4
- Environmental Conditions 5
- Regulatory Markings 6
- Table of Contents 9
- 3 DC Power Supply Operation 10
- 4 System-Related Operation 11
- 6 List of Error Messages 12
- List of Figures 13
- XIV U3606B User’s Guide 14
- List of Tables 15
- XVI U3606B User’s Guide 16
- Introduction 17
- About This Manual 18
- Preparing the U3606B 19
- 1 Introduction 20
- 4 U3606B User’s Guide 20
- Adjust the carry handle 23
- Rack mount the instrument 24
- Introduction 1 25
- U3606B User’s Guide 9 25
- Stack multiple U3606B units 26
- The U3606B in Brief 27
- Overview 28
- Rear panel 29
- 14 U3606B User’s Guide 30
- Display screen 31
- 16 U3606B User’s Guide 32
- U3606B User’s Guide 17 33
- Using the Shift key 35
- 20 U3606B User’s Guide 36
- U3606B User’s Guide 21 37
- 22 U3606B User’s Guide 38
- U3606B User’s Guide 23 39
- Input/Output terminals 40
- U3606B User’s Guide 25 41
- 26 U3606B User’s Guide 42
- U3606B User’s Guide 27 43
- 28 U3606B User’s Guide 44
- Operation and Features 45
- Measuring Voltage 46
- Voltage measurement summary 47
- Using the AC+DC function 48
- Measuring Current 49
- Current measurement summary 50
- Measuring Resistance 52
- Operation and Features 2 53
- U3606B User’s Guide 37 53
- 2 Operation and Features 54
- 38 U3606B User’s Guide 54
- Test ing Conti nuity 55
- Test current 56
- Continuity test summary 57
- Measuring Low-Resistance 58
- U3606B User’s Guide 43 59
- U3606B User’s Guide 45 61
- 46 U3606B User’s Guide 62
- Measuring Capacitance 63
- 48 U3606B User’s Guide 64
- Measuring tips 65
- Test ing Diodes 66
- Testing Diodes 67
- U3606B User’s Guide 51 67
- Diode test summary 68
- Testi ng ti ps 68
- Connect the test leads 69
- U3606B User’s Guide 55 71
- 58 U3606B User’s Guide 74
- Setting the Resolution 77
- Math Operations 78
- Enable the null function 80
- Edit the null value 81
- Enable the dBm function 82
- Enable the dB function 83
- Edit the relative value 84
- Enable the MinMax function 85
- *RST command) 86
- Enable the Limit function 87
- 72 U3606B User’s Guide 88
- Enable the Hold function 90
- Triggering the Multimeter 91
- Front panel triggering 92
- Remote interface triggering 93
- DC Power Supply Operation 95
- Constant Voltage Operation 96
- U3606B User’s Guide 81 97
- Constant Current Operation 100
- 84 U3606B User’s Guide 100
- Enable the output 101
- Protection Functions 102
- Select the OVP function 103
- Checking the OVP operation 104
- Resetting the OVP condition 105
- Over-current protection (OCP) 106
- Select the OCP function 107
- Checking the OCP operation 108
- Resetting the OCP condition 109
- Over-voltage limit (OV) 110
- Select the OV function 111
- Over-current limit (OC) 113
- Select the OC function 114
- Square-Wave Operation 116
- DC Power Supply Operation 3 117
- U3606B User’s Guide 101 117
- U3606B User’s Guide 103 119
- Sweep Functions 122
- Connect the load 123
- 108 U3606B User’s Guide 124
- Scan signal 125
- U3606B User’s Guide 111 127
- Selecting a Range 129
- Enabling the Output 130
- Remote Sensing 131
- +S + + – – –S 132
- U3606B User’s Guide 119 135
- Enable remote sensing 136
- Stability 137
- CV regulation 137
- Output rating 137
- Output noise 138
- System-Related Operation 139
- Using the Utility Menu 140
- System-Related Operation 4 141
- U3606B User’s Guide 125 141
- Utility Menu Summary 142
- U3606B User’s Guide 127 143
- 128 U3606B User’s Guide 144
- Utility Menu Items 145
- Enabling refresh hold 148
- Setting the smooth function 149
- Amplitude end position 155
- (NN.NNN V or N.NNNN A) 155
- Number of 155
- Performing a self-test 158
- Configuring the beeper 160
- Changing the power-on state 161
- Storing a state 164
- Recalling a stored state 165
- Remote Operation 166
- GPIB address 167
- SCPI commands 168
- SCPI language version 169
- SCPI query time-out 169
- 154 U3606B User’s Guide 170
- Agilent Technologies 171
- Product Characteristics 172
- U3606B User’s Guide 157 173
- Specification assumptions 174
- DC specifications 175
- 160 U3606B User’s Guide 176
- U3606B User’s Guide 161 177
- AC specifications 179
- Frequency specifications 181
- 166 U3606B User’s Guide 182
- Operating specifications 183
- 168 U3606B User’s Guide 184
- (continued) 184
- Supplemental characteristics 185
- 170 U3606B User’s Guide 186
- U3606B User’s Guide 171 187
- 172 U3606B User’s Guide 188
- Safety considerations 189
- Specifications assumptions 189
- Performance specifications 190
- U3606B User’s Guide 175 191
- U3606B User’s Guide 177 193
- Sweep characteristics 195
- 180 U3606B User’s Guide 196
- List of Error Messages 197
- Error Messages 198
- Command errors 199
- Execution errors 200
- Internal errors 201
- Query errors 201
- Device specific errors 201
- Self-test errors 202
- Calibration errors 203
- 188 U3606B User’s Guide 204
Manuais e produtos relacionados com Multímetros Agilent Technologies U3606B
(21 páginas)
Multímetros Agilent Technologies 8568B Especificações
(118 páginas)
(118 páginas)
Multímetros Agilent Technologies DC140 Manual de Serviço
(287 páginas)
(287 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais