Agilent Technologies InfiniiVision 5000 Series Manual de Serviço Página 481
- Página / 884
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Commands by Subsystem 5
Agilent InfiniiVision 5000 Series Oscilloscopes Programmer's Guide 481
:TRIGger:FLEXray:AUTosetup
(see page 750)
Command Syntax
:TRIGger:FLEXray:AUTosetup
The :TRIGger:FLEXray:AUTosetup command automatically configures
oscilloscope settings to facilitate FlexRay triggering and serial decode.
• Sets the selected source channel's impedance to 50 Ohms.
• Sets the selected source channel' s probe attenuation to 10:1.
• Sets the trigger level (on the selected source channel) to - 300 mV.
• Turns on trigger Noise Reject.
• Turns on Serial Decode.
• Sets the trigger type to FlexRay.
See Also • "Introduction to :TRIGger Commands" on page 440
• ":TRIGger:FLEXray:TRIGger" on page 491
• ":TRIGger:FLEXray:BAUDrate" on page 482
• ":TRIGger[:EDGE]:LEVel" on page 476
• ":TRIGger:FLEXray:SOURce" on page 490
NOTE
This command is only valid when the FLEXray triggering and serial decode option (Option
FLX) has been licensed.
- Agilent InfiniiVision 1
- 5000 Series 1
- Oscilloscopes 1
- In This Book 3
- Contents 5
- 6 Commands A-Z 17
- 8 Error Messages 18
- 9 Status Reporting 18
- 10 Synchronizing Acquisitions 19
- 12 Programming Examples 19
- What's New 21
- 1 What's New 22
- Commands 31
- Obsolete 31
- Version 4.00 at Introduction 36
- Setting Up 37
- 2 Setting Up 38
- Using the LAN Interface 39
- Using the GPIB Interface 40
- Setting Up 2 41
- Address 43
- Click Test Connection 43
- Getting Started 47
- Initializing 48
- Capturing Data 48
- Analyzing Captured Data 49
- Programming the Oscilloscope 50
- 3 Getting Started 52
- Getting Started 3 53
- Ensure New Data is Collected 54
- Checking Instrument Status 58
- Telnet Sockets 59
- Commands Quick Reference 61
- Command Summary 62
- 4 Commands Quick Reference 100
- Syntax Elements 106
- Commands Quick Reference 4 107
- Commands by Subsystem 109
- 5 Commands by Subsystem 110
- Common (*) Commands 111
- *CLS (Clear Status) 115
- Commands by Subsystem 5 119
- *IDN (Identification Number) 120
- *LRN (Learn Device Setup) 121
- *OPC (Operation Complete) 122
- *OPT (Option Identification) 123
- *RCL (Recall) 124
- *RST (Reset) 125
- Example Code 127
- *SAV (Save) 128
- *SRE (Service Request Enable) 129
- *STB (Read Status Byte) 131
- *TRG (Trigger) 133
- *TST (Self Test) 134
- *WAI (Wait To Continue) 135
- Root (:) Commands 136
- :AER (Arm Event Register) 139
- :AUToscale 140
- :AUToscale:AMODE 142
- :AUToscale:CHANnels 143
- :CDISplay 145
- :DIGitize 146
- :MTEenable <mask> 155
- :MTEenable? 155
- :MTERegister[:EVENt]? 157
- <value><NL> 157
- :OPEE <mask> 159
- (see page 750) 161
- Query Syntax 161
- :OVLRegister? 167
- Return Format: 171
- :TER (Trigger Event Register) 175
- :ACQuire Commands 177
- :ACQuire:AALias 179
- :ACQuire:COMPlete 180
- :ACQuire:COUNt 181
- :ACQuire:DAALias 182
- :ACQuire:MODE 183
- :ACQuire:POINts 184
- :ACQuire:SEGMented:ANALyze 185
- :ACQuire:SEGMented:COUNt 186
- :ACQuire:SEGMented:INDex 187
- :ACQuire:SRATe 190
- :ACQuire:TYPE 191
- :CALibrate Commands 193
- :CALibrate:DATE 195
- :CALibrate:LABel 196
- :CALibrate:OUTPut 197
- :CALibrate:STARt 198
- :CALibrate:STATus 199
- :CALibrate:SWITch 200
- :CALibrate:TEMPerature 201
- :CALibrate:TIME 202
- :CHANnel<n> Commands 203
- :CHANnel<n>:BWLimit 206
- :CHANnel<n>:COUPling 207
- :CHANnel<n>:DISPlay 208
- :CHANnel<n>:IMPedance 209
- :CHANnel<n>:INVert 210
- :CHANnel<n>:LABel 211
- :CHANnel<n>:OFFSet 212
- :CHANnel<n>:PROBe 213
- :CHANnel<n>:PROBe:ID 215
- :CHANnel<n>:PROBe:SKEW 216
- :CHANnel<n>:PROBe:STYPe 217
- :CHANnel<n>:PROTection 218
- :CHANnel<n>:RANGe 219
- :CHANnel<n>:SCALe 220
- :CHANnel<n>:UNITs 221
- :CHANnel<n>:VERNier 222
- :DISPlay Commands 223
- :DISPlay:CLEar 225
- :DISPlay:DATA 226
- :DISPlay:LABel 228
- :DISPlay:LABList 229
- :DISPlay:PERSistence 230
- :DISPlay:SOURce 231
- :DISPlay:VECTors 232
- :EXTernal Trigger Commands 233
- :EXTernal:BWLimit 235
- :EXTernal:IMPedance 236
- :EXTernal:PROBe 237
- :EXTernal:PROBe:ID 238
- :EXTernal:PROTection 240
- :EXTernal:RANGe 241
- :EXTernal:UNITs 242
- :FUNCtion Commands 243
- :FUNCtion:CENTer 246
- :FUNCtion:DISPlay 247
- :FUNCtion:GOFT:OPERation 248
- :FUNCtion:GOFT:SOURce1 249
- :FUNCtion:GOFT:SOURce2 250
- :FUNCtion:OFFSet 251
- :FUNCtion:OPERation 252
- :FUNCtion:RANGe 253
- :FUNCtion:REFerence 254
- :FUNCtion:SCALe 255
- :FUNCtion:SOURce1 256
- :FUNCtion:SOURce2 257
- :FUNCtion:SPAN 258
- :FUNCtion:WINDow 259
- :HARDcopy Commands 260
- :HARDcopy:AREA 262
- :HARDcopy:APRinter 263
- :HARDcopy:FACTors 264
- :HARDcopy:FFEed 265
- :HARDcopy:INKSaver 266
- :HARDcopy:LAYout 267
- :HARDcopy:PALette 268
- :HARDcopy:PRINter:LIST 269
- :HARDcopy:STARt 270
- :LISTer Commands 271
- :LISTer:DATA 272
- :LISTer:DISPlay 273
- :MARKer Commands 274
- :MARKer:MODE 276
- :MARKer:X1Position 277
- :MARKer:X1Y1source 278
- :MARKer:X2Position 279
- :MARKer:X2Y2source 280
- :MARKer:XDELta 281
- :MARKer:Y1Position 282
- :MARKer:Y2Position 283
- :MARKer:YDELta 284
- :MEASure Commands 285
- :MEASure:CLEar 292
- :MEASure:COUNter 293
- :MEASure:DEFine 294
- :MEASure:DELay 297
- :MEASure:DUTYcycle 299
- :MEASure:FALLtime 300
- :MEASure:FREQuency 301
- :MEASure:NWIDth 302
- :MEASure:OVERshoot 303
- :MEASure:PERiod 305
- :MEASure:PHASe 306
- :MEASure:PREShoot 307
- :MEASure:PWIDth 308
- :MEASure:RESults 309
- :MEASure:RISetime 312
- :MEASure:SDEViation 313
- :MEASure:SHOW 314
- :MEASure:SOURce 315
- :MEASure:STATistics 317
- :MEASure:STATistics:INCRement 318
- :MEASure:STATistics:RESet 319
- :MEASure:TEDGe 320
- :MEASure:TVALue 322
- :MEASure:VAMPlitude 324
- :MEASure:VAVerage 325
- :MEASure:VBASe 326
- :MEASure:VMAX 327
- :MEASure:VMIN 328
- :MEASure:VPP 329
- :MEASure:VRATio 330
- :MEASure:VRMS 331
- :MEASure:VTIMe 332
- :MEASure:VTOP 333
- :MEASure:WINDow 334
- :MEASure:XMAX 335
- :MEASure:XMIN 336
- :MTESt Commands 337
- :MTESt:AMASk:CREate 342
- :MTESt:AMASk:SOURce 343
- :MTESt:AMASk:UNITs 344
- :MTESt:AMASk:XDELta 345
- :MTESt:AMASk:YDELta 346
- :MTESt:COUNt:FWAVeforms 347
- :MTESt:COUNt:RESet 348
- :MTESt:COUNt:TIME 349
- :MTESt:COUNt:WAVeforms 350
- :MTESt:DATA 351
- :MTESt:DELete 352
- :MTESt:ENABle 353
- :MTESt:LOCK 354
- :MTESt:OUTPut 355
- :MTESt:RMODe 356
- :MTESt:RMODe:FACTion:MEASure 357
- :MTESt:RMODe:FACTion:PRINt 358
- :MTESt:RMODe:FACTion:SAVE 359
- :MTESt:RMODe:FACTion:STOP 360
- :MTESt:RMODe:SIGMa 361
- :MTESt:RMODe:TIME 362
- :MTESt:RMODe:WAVeforms 363
- :MTESt:SCALe:BIND 364
- :MTESt:SCALe:X1 365
- :MTESt:SCALe:XDELta 366
- :MTESt:SCALe:Y1 367
- :MTESt:SCALe:Y2 368
- :MTESt:SOURce 369
- :MTESt:TITLe 370
- :RECall Commands 371
- :RECall:FILename 372
- :RECall:IMAGe[:STARt] 373
- :RECall:MASK[:STARt] 374
- :RECall:PWD 375
- :RECall:SETup[:STARt] 376
- :SAVE Commands 377
- :SAVE:FILename 379
- :SAVE:IMAGe[:STARt] 380
- :SAVE:IMAGe:AREA 381
- :SAVE:IMAGe:FACTors 382
- :SAVE:IMAGe:FORMat 383
- :SAVE:IMAGe:INKSaver 384
- :SAVE:IMAGe:PALette 385
- :SAVE:LISTer[:STARt] 386
- :SAVE:MASK[:STARt] 387
- :SAVE:PWD 388
- :SAVE:SETup[:STARt] 389
- :SAVE:WAVeform[:STARt] 390
- :SAVE:WAVeform:FORMat 391
- :SAVE:WAVeform:LENGth 392
- :SAVE:WAVeform:SEGMented 393
- :SBUS Commands 394
- :SBUS:DISP 0;MODE IIC 395
- :SBUS:CAN:COUNt:ERRor 396
- :SBUS:CAN:COUNt:OVERload 397
- :SBUS:CAN:COUNt:RESet 398
- :SBUS:CAN:COUNt:TOTal 399
- :SBUS:CAN:COUNt:UTILization 400
- :SBUS:DISPlay 401
- :SBUS:FLEXray:COUNt:NULL 402
- :SBUS:FLEXray:COUNt:RESet 403
- :SBUS:FLEXray:COUNt:SYNC 404
- :SBUS:FLEXray:COUNt:TOTal 405
- :SBUS:I2S:BASE 406
- :SBUS:IIC:ASIZe 407
- :SBUS:LIN:PARity 408
- :SBUS:M1553:BASE 409
- :SBUS:MODE 410
- :SBUS:SPI:BITorder 411
- :SBUS:SPI:WIDTh 412
- :SBUS:UART:BASE 413
- :SBUS:UART:COUNt:ERRor 414
- :SBUS:UART:COUNt:RESet 415
- :SBUS:UART:COUNt:RXFRames 416
- :SBUS:UART:COUNt:TXFRames 417
- :SBUS:UART:FRAMing 418
- :SYSTem Commands 419
- :SYSTem:DATE 420
- :SYSTem:DSP 421
- :SYSTem:ERRor 422
- :SYSTem:LOCK 423
- :SYSTem:PRECision 424
- :SYSTem:PROTection:LOCK 425
- :SYSTem:SETup 426
- :SYSTem:TIME 428
- :TIMebase Commands 429
- :TIMebase:MODE 431
- :TIMebase:POSition 432
- :TIMebase:RANGe 433
- :TIMebase:REFerence 434
- :TIMebase:SCALe 435
- :TIMebase:VERNier 436
- :TIMebase:WINDow:POSition 437
- :TIMebase:WINDow:RANGe 438
- :TIMebase:WINDow:SCALe 439
- :TRIGger Commands 440
- General :TRIGger Commands 443
- :TRIGger:HFReject 444
- :TRIGger:HOLDoff 445
- :TRIGger:LFIFty 446
- :TRIGger:MODE 447
- :TRIGger:NREJect 448
- :TRIGger:PATTern 449
- :TRIGger:SWEep 451
- :TRIGger:CAN Commands 452
- :TRIGger:CAN:PATTern:DATA 454
- :TRIGger:CAN:PATTern:ID 456
- :TRIGger:CAN:PATTern:ID:MODE 457
- :TRIGger:CAN:SAMPlepoint 458
- :TRIGger:CAN:SIGNal:BAUDrate 459
- :TRIGger:CAN:SOURce 461
- :TRIGger:CAN:TRIGger 462
- :TRIGger:DURation Commands 464
- :TRIGger:DURation:GREaterthan 465
- :TRIGger:DURation:LESSthan 466
- :TRIGger:DURation:PATTern 467
- :TRIGger:DURation:QUALifier 468
- :TRIGger:DURation:RANGe 469
- :TRIGger:EBURst Commands 470
- :TRIGger:EBURst:COUNt 471
- :TRIGger:EBURst:IDLE 472
- :TRIGger:EBURst:SLOPe 473
- :TRIGger[:EDGE] Commands 474
- :TRIGger[:EDGE]:COUPling 475
- :TRIGger[:EDGE]:LEVel 476
- :TRIGger[:EDGE]:REJect 477
- :TRIGger[:EDGE]:SLOPe 478
- :TRIGger[:EDGE]:SOURce 479
- :TRIGger:FLEXray Commands 480
- :TRIGger:FLEXray:AUTosetup 481
- :TRIGger:FLEXray:BAUDrate 482
- :TRIGger:FLEXray:CHANnel 483
- :TRIGger:FLEXray:ERRor:TYPE 484
- :TRIGger:FLEXray:EVENt:TYPE 485
- :TRIGger:FLEXray:FRAMe:CCBase 486
- :TRIGger:FLEXray:FRAMe:ID 488
- :TRIGger:FLEXray:FRAMe:TYPE 489
- :TRIGger:FLEXray:SOURce 490
- :TRIGger:FLEXray:TRIGger 491
- :TRIGger:GLITch Commands 492
- :TRIGger:GLITch:GREaterthan 493
- :TRIGger:GLITch:LESSthan 494
- :TRIGger:GLITch:LEVel 495
- :TRIGger:GLITch:POLarity 496
- :TRIGger:GLITch:QUALifier 497
- :TRIGger:GLITch:RANGe 498
- :TRIGger:GLITch:SOURce 499
- :TRIGger:I2S Commands 500
- :TRIGger:I2S:ALIGnment 502
- :TRIGger:I2S:AUDio 503
- :TRIGger:I2S:CLOCk:SLOPe 504
- :TRIGger:I2S:PATTern:DATA 505
- :TRIGger:I2S:PATTern:FORMat 507
- :TRIGger:I2S:RANGe 508
- :TRIGger:I2S:RWIDth 510
- :TRIGger:I2S:SOURce:CLOCk 511
- :TRIGger:I2S:SOURce:DATA 512
- :TRIGger:I2S:SOURce:WSELect 513
- :TRIGger:I2S:TRIGger 514
- :TRIGger:I2S:TWIDth 516
- :TRIGger:I2S:WSLow 517
- :TRIGger:IIC Commands 518
- :TRIGger:IIC:PATTern:ADDRess 519
- :TRIGger:IIC:PATTern:DATA 520
- :TRIGger:IIC:PATTern:DATa2 521
- :TRIGger:IIC[:SOURce]:CLOCk 522
- :TRIGger:IIC[:SOURce]:DATA 523
- :TRIGger:IIC:TRIGger[:TYPE] 525
- :TRIGger:LIN Commands 527
- :TRIGger:LIN:ID 529
- :TRIGger:LIN:PATTern:DATA 530
- :TRIGger:LIN:PATTern:FORMat 533
- :TRIGger:LIN:SAMPlepoint 534
- :TRIGger:LIN:SIGNal:BAUDrate 535
- :TRIGger:LIN:SOURce 536
- :TRIGger:LIN:STANdard 537
- :TRIGger:LIN:SYNCbreak 538
- :TRIGger:LIN:TRIGger 539
- :TRIGger:M1553 Commands 540
- :TRIGger:M1553:AUTosetup 541
- :TRIGger:M1553:PATTern:DATA 542
- :TRIGger:M1553:RTA 543
- :TRIGger:M1553:SOURce:LOWer 544
- :TRIGger:M1553:SOURce:UPPer 545
- :TRIGger:M1553:TYPE 546
- :TRIGger:SEQuence Commands 547
- :TRIGger:SEQuence:COUNt 548
- :TRIGger:SEQuence:EDGE 549
- :TRIGger:SEQuence:FIND 550
- :TRIGger:SEQuence:PATTern 551
- :TRIGger:SEQuence:RESet 552
- :TRIGger:SEQuence:TIMer 553
- :TRIGger:SEQuence:TRIGger 554
- :TRIGger:SPI Commands 555
- :TRIGger:SPI:CLOCk:SLOPe 556
- :TRIGger:SPI:CLOCk:TIMeout 557
- :TRIGger:SPI:FRAMing 558
- :TRIGger:SPI:PATTern:DATA 559
- :TRIGger:SPI:PATTern:WIDTh 560
- :TRIGger:SPI:SOURce:CLOCk 561
- :TRIGger:SPI:SOURce:DATA 562
- :TRIGger:SPI:SOURce:FRAMe 563
- :TRIGger:TV Commands 564
- :TRIGger:TV:LINE 565
- :TRIGger:TV:MODE 566
- :TRIGger:TV:POLarity 567
- :TRIGger:TV:SOURce 568
- :TRIGger:TV:STANdard 569
- :TRIGger:UART Commands 570
- :TRIGger:UART:BASE 572
- :TRIGger:UART:BAUDrate 573
- :TRIGger:UART:BITorder 574
- :TRIGger:UART:BURSt 575
- :TRIGger:UART:DATA 576
- :TRIGger:UART:IDLE 577
- :TRIGger:UART:PARity 578
- :TRIGger:UART:POLarity 579
- :TRIGger:UART:QUALifier 580
- :TRIGger:UART:SOURce:RX 581
- :TRIGger:UART:SOURce:TX 582
- :TRIGger:UART:TYPE 583
- :TRIGger:UART:WIDTh 584
- :TRIGger:USB Commands 585
- :TRIGger:USB:SOURce:DMINus 586
- :TRIGger:USB:SOURce:DPLus 587
- :TRIGger:USB:SPEed 588
- :TRIGger:USB:TRIGger 589
- :WAVeform Commands 590
- :WAVeform:BYTeorder 597
- :WAVeform:COUNt 598
- :WAVeform:DATA 599
- :WAVeform:FORMat 601
- :WAVeform:POINts 602
- :WAVeform:POINts:MODE 604
- :WAVeform:PREamble 606
- #Vsteps = 607
- :WAVeform:SEGMented:COUNt 609
- :WAVeform:SEGMented:TTAG 610
- :WAVeform:SOURce 611
- :WAVeform:SOURce:SUBSource 615
- :WAVeform:TYPE 616
- :WAVeform:UNSigned 617
- :WAVeform:VIEW 618
- :WAVeform:XINCrement 619
- :WAVeform:XORigin 620
- :WAVeform:XREFerence 621
- :WAVeform:YINCrement 622
- :WAVeform:YORigin 623
- :WAVeform:YREFerence 624
- Commands A-Z 625
- Commands A-Z 6 627
- Commands" on page 750) 657
- Discontinued 661
- Parameters 661
- :CHANnel:LABel 662
- :CHANnel2:SKEW 663
- :CHANnel<n>:INPut 664
- :CHANnel<n>:PMODe 665
- :DISPlay:CONNect 666
- Command Syntax 667
- :EXTernal:INPut 668
- :EXTernal:PMODe 669
- :FUNCtion:SOURce 670
- :FUNCtion:VIEW 671
- :HARDcopy:DESTination 672
- :HARDcopy:DEVice 673
- :HARDcopy:FILename 674
- :HARDcopy:FORMat 675
- :HARDcopy:GRAYscale 676
- :HARDcopy:IGColors 677
- :HARDcopy:PDRiver 678
- :MEASure:LOWer 679
- :MEASure:SCRatch 680
- :MEASure:TDELta 681
- :MEASure:THResholds 682
- :MEASure:TMAX 683
- :MEASure:TMIN 684
- :MEASure:TSTArt 685
- :MEASure:TSTOp 686
- :MEASure:TVOLt 687
- :MEASure:UPPer 689
- :MEASure:VDELta 690
- :MEASure:VSTArt 691
- :MEASure:VSTOp 692
- :MTESt:AMASk:{SAVE 693
- :MTESt:AVERage 694
- :MTESt:AVERage:COUNt 695
- :MTESt:LOAD 696
- :MTESt:RUMode 697
- :MTESt:RUMode:SOFailure 698
- :MTESt:{STARt 699
- :MTESt:TRIGger:SOURce 700
- DISK invalid 702
- PCL invalid 702
- Old Print Option: Is Now: 702
- :TIMebase:DELay 703
- :TRIGger:CAN:ACKNowledge 704
- <value> ::= LIN 705
- :TRIGger:TV:TVMode 706
- Error Messages 707
- Error Messages 8 709
- Status Reporting 715
- Status Reporting 9 717
- Status Byte Register (STB) 721
- Trigger Event Register (TER) 724
- Output Queue 725
- Message Queue 726
- Error Queue 729
- Status Condition Register 731
- Arm Event Register (AER) 732
- Event Condition Register 735
- Clearing Registers and Queues 737
- Synchronizing Acquisitions 739
- Set Up the Oscilloscope 740
- Acquire a Waveform 740
- Retrieve Results 740
- Blocking Synchronization 741
- Synchronizing Acquisitions 10 743
- Command Classifications 750 749
- Query Return Values 772 749
- Command Classifications 750
- ":DISPLAY:LABEL ON" 751
- Program Message 751
- Instruction Header 751
- Separator 751
- Program Data 751
- Simple Command Headers 753
- Compound Command Headers 753
- Common Command Headers 754
- Program Data Syntax Rules 754
- Command Tree 755
- Duplicate Mnemonics 769
- Query Return Values 772
- Programming Examples 775
- VISA COM Examples 776
- Programming Examples 12 777
- " + _ 783
- VISA COM Example in C# 786
- VISA Examples 809
- VISA Example in Visual Basic 818
- VISA Example in C# 828
- SICL Examples 855
- SICL Example in Visual Basic 864
- Numerics 873
- , 251, 254 877
- function, 251, 254 879
Manuais e produtos relacionados com Multímetros Agilent Technologies InfiniiVision 5000 Series
Multímetros Agilent Technologies 34401A Especificações
(482 páginas)
(482 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.144 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais