Agilent Technologies InfiniiVision 5000 Series Manual de Serviço Página 291
- Página / 884
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Commands by Subsystem 5
Agilent InfiniiVision 5000 Series Oscilloscopes Programmer's Guide 291
When making measurements in the zoomed (delayed) time base mode
(:TIMebase:MODE WINDow), the oscilloscope will attempt to make the
measurement inside the zoomed sweep window. If the measurement is an
average and there are not three edges, the oscilloscope will revert to the
mode of making the measurement at the start of the main sweep.
When the command form is used, the measurement result is displayed on
the instrument. When the query form of these measurements is used, the
measurement is made one time, and the measurement result is returned
over the bus.
Measurements are made on the displayed waveforms specified by the
:MEASure:SOURce command. The MATH source is an alias for the
FUNCtion source.
Not all measurements are available on the FFT (Fast Fourier Transform).
Reporting the Setup
Use the :MEASure? query to obtain setup information for the MEASure
subsystem. (Currently, this is only :MEASure:SOURce.)
Return Format
The following is a sample response from the :MEASure? query. In this
case, the query was issued following a *RST command.
:MEAS:SOUR CHAN1,CHAN2;STAT ON
- Agilent InfiniiVision 1
- 5000 Series 1
- Oscilloscopes 1
- In This Book 3
- Contents 5
- 6 Commands A-Z 17
- 8 Error Messages 18
- 9 Status Reporting 18
- 10 Synchronizing Acquisitions 19
- 12 Programming Examples 19
- What's New 21
- 1 What's New 22
- Commands 31
- Obsolete 31
- Version 4.00 at Introduction 36
- Setting Up 37
- 2 Setting Up 38
- Using the LAN Interface 39
- Using the GPIB Interface 40
- Setting Up 2 41
- Address 43
- Click Test Connection 43
- Getting Started 47
- Initializing 48
- Capturing Data 48
- Analyzing Captured Data 49
- Programming the Oscilloscope 50
- 3 Getting Started 52
- Getting Started 3 53
- Ensure New Data is Collected 54
- Checking Instrument Status 58
- Telnet Sockets 59
- Commands Quick Reference 61
- Command Summary 62
- 4 Commands Quick Reference 100
- Syntax Elements 106
- Commands Quick Reference 4 107
- Commands by Subsystem 109
- 5 Commands by Subsystem 110
- Common (*) Commands 111
- *CLS (Clear Status) 115
- Commands by Subsystem 5 119
- *IDN (Identification Number) 120
- *LRN (Learn Device Setup) 121
- *OPC (Operation Complete) 122
- *OPT (Option Identification) 123
- *RCL (Recall) 124
- *RST (Reset) 125
- Example Code 127
- *SAV (Save) 128
- *SRE (Service Request Enable) 129
- *STB (Read Status Byte) 131
- *TRG (Trigger) 133
- *TST (Self Test) 134
- *WAI (Wait To Continue) 135
- Root (:) Commands 136
- :AER (Arm Event Register) 139
- :AUToscale 140
- :AUToscale:AMODE 142
- :AUToscale:CHANnels 143
- :CDISplay 145
- :DIGitize 146
- :MTEenable <mask> 155
- :MTEenable? 155
- :MTERegister[:EVENt]? 157
- <value><NL> 157
- :OPEE <mask> 159
- (see page 750) 161
- Query Syntax 161
- :OVLRegister? 167
- Return Format: 171
- :TER (Trigger Event Register) 175
- :ACQuire Commands 177
- :ACQuire:AALias 179
- :ACQuire:COMPlete 180
- :ACQuire:COUNt 181
- :ACQuire:DAALias 182
- :ACQuire:MODE 183
- :ACQuire:POINts 184
- :ACQuire:SEGMented:ANALyze 185
- :ACQuire:SEGMented:COUNt 186
- :ACQuire:SEGMented:INDex 187
- :ACQuire:SRATe 190
- :ACQuire:TYPE 191
- :CALibrate Commands 193
- :CALibrate:DATE 195
- :CALibrate:LABel 196
- :CALibrate:OUTPut 197
- :CALibrate:STARt 198
- :CALibrate:STATus 199
- :CALibrate:SWITch 200
- :CALibrate:TEMPerature 201
- :CALibrate:TIME 202
- :CHANnel<n> Commands 203
- :CHANnel<n>:BWLimit 206
- :CHANnel<n>:COUPling 207
- :CHANnel<n>:DISPlay 208
- :CHANnel<n>:IMPedance 209
- :CHANnel<n>:INVert 210
- :CHANnel<n>:LABel 211
- :CHANnel<n>:OFFSet 212
- :CHANnel<n>:PROBe 213
- :CHANnel<n>:PROBe:ID 215
- :CHANnel<n>:PROBe:SKEW 216
- :CHANnel<n>:PROBe:STYPe 217
- :CHANnel<n>:PROTection 218
- :CHANnel<n>:RANGe 219
- :CHANnel<n>:SCALe 220
- :CHANnel<n>:UNITs 221
- :CHANnel<n>:VERNier 222
- :DISPlay Commands 223
- :DISPlay:CLEar 225
- :DISPlay:DATA 226
- :DISPlay:LABel 228
- :DISPlay:LABList 229
- :DISPlay:PERSistence 230
- :DISPlay:SOURce 231
- :DISPlay:VECTors 232
- :EXTernal Trigger Commands 233
- :EXTernal:BWLimit 235
- :EXTernal:IMPedance 236
- :EXTernal:PROBe 237
- :EXTernal:PROBe:ID 238
- :EXTernal:PROTection 240
- :EXTernal:RANGe 241
- :EXTernal:UNITs 242
- :FUNCtion Commands 243
- :FUNCtion:CENTer 246
- :FUNCtion:DISPlay 247
- :FUNCtion:GOFT:OPERation 248
- :FUNCtion:GOFT:SOURce1 249
- :FUNCtion:GOFT:SOURce2 250
- :FUNCtion:OFFSet 251
- :FUNCtion:OPERation 252
- :FUNCtion:RANGe 253
- :FUNCtion:REFerence 254
- :FUNCtion:SCALe 255
- :FUNCtion:SOURce1 256
- :FUNCtion:SOURce2 257
- :FUNCtion:SPAN 258
- :FUNCtion:WINDow 259
- :HARDcopy Commands 260
- :HARDcopy:AREA 262
- :HARDcopy:APRinter 263
- :HARDcopy:FACTors 264
- :HARDcopy:FFEed 265
- :HARDcopy:INKSaver 266
- :HARDcopy:LAYout 267
- :HARDcopy:PALette 268
- :HARDcopy:PRINter:LIST 269
- :HARDcopy:STARt 270
- :LISTer Commands 271
- :LISTer:DATA 272
- :LISTer:DISPlay 273
- :MARKer Commands 274
- :MARKer:MODE 276
- :MARKer:X1Position 277
- :MARKer:X1Y1source 278
- :MARKer:X2Position 279
- :MARKer:X2Y2source 280
- :MARKer:XDELta 281
- :MARKer:Y1Position 282
- :MARKer:Y2Position 283
- :MARKer:YDELta 284
- :MEASure Commands 285
- :MEASure:CLEar 292
- :MEASure:COUNter 293
- :MEASure:DEFine 294
- :MEASure:DELay 297
- :MEASure:DUTYcycle 299
- :MEASure:FALLtime 300
- :MEASure:FREQuency 301
- :MEASure:NWIDth 302
- :MEASure:OVERshoot 303
- :MEASure:PERiod 305
- :MEASure:PHASe 306
- :MEASure:PREShoot 307
- :MEASure:PWIDth 308
- :MEASure:RESults 309
- :MEASure:RISetime 312
- :MEASure:SDEViation 313
- :MEASure:SHOW 314
- :MEASure:SOURce 315
- :MEASure:STATistics 317
- :MEASure:STATistics:INCRement 318
- :MEASure:STATistics:RESet 319
- :MEASure:TEDGe 320
- :MEASure:TVALue 322
- :MEASure:VAMPlitude 324
- :MEASure:VAVerage 325
- :MEASure:VBASe 326
- :MEASure:VMAX 327
- :MEASure:VMIN 328
- :MEASure:VPP 329
- :MEASure:VRATio 330
- :MEASure:VRMS 331
- :MEASure:VTIMe 332
- :MEASure:VTOP 333
- :MEASure:WINDow 334
- :MEASure:XMAX 335
- :MEASure:XMIN 336
- :MTESt Commands 337
- :MTESt:AMASk:CREate 342
- :MTESt:AMASk:SOURce 343
- :MTESt:AMASk:UNITs 344
- :MTESt:AMASk:XDELta 345
- :MTESt:AMASk:YDELta 346
- :MTESt:COUNt:FWAVeforms 347
- :MTESt:COUNt:RESet 348
- :MTESt:COUNt:TIME 349
- :MTESt:COUNt:WAVeforms 350
- :MTESt:DATA 351
- :MTESt:DELete 352
- :MTESt:ENABle 353
- :MTESt:LOCK 354
- :MTESt:OUTPut 355
- :MTESt:RMODe 356
- :MTESt:RMODe:FACTion:MEASure 357
- :MTESt:RMODe:FACTion:PRINt 358
- :MTESt:RMODe:FACTion:SAVE 359
- :MTESt:RMODe:FACTion:STOP 360
- :MTESt:RMODe:SIGMa 361
- :MTESt:RMODe:TIME 362
- :MTESt:RMODe:WAVeforms 363
- :MTESt:SCALe:BIND 364
- :MTESt:SCALe:X1 365
- :MTESt:SCALe:XDELta 366
- :MTESt:SCALe:Y1 367
- :MTESt:SCALe:Y2 368
- :MTESt:SOURce 369
- :MTESt:TITLe 370
- :RECall Commands 371
- :RECall:FILename 372
- :RECall:IMAGe[:STARt] 373
- :RECall:MASK[:STARt] 374
- :RECall:PWD 375
- :RECall:SETup[:STARt] 376
- :SAVE Commands 377
- :SAVE:FILename 379
- :SAVE:IMAGe[:STARt] 380
- :SAVE:IMAGe:AREA 381
- :SAVE:IMAGe:FACTors 382
- :SAVE:IMAGe:FORMat 383
- :SAVE:IMAGe:INKSaver 384
- :SAVE:IMAGe:PALette 385
- :SAVE:LISTer[:STARt] 386
- :SAVE:MASK[:STARt] 387
- :SAVE:PWD 388
- :SAVE:SETup[:STARt] 389
- :SAVE:WAVeform[:STARt] 390
- :SAVE:WAVeform:FORMat 391
- :SAVE:WAVeform:LENGth 392
- :SAVE:WAVeform:SEGMented 393
- :SBUS Commands 394
- :SBUS:DISP 0;MODE IIC 395
- :SBUS:CAN:COUNt:ERRor 396
- :SBUS:CAN:COUNt:OVERload 397
- :SBUS:CAN:COUNt:RESet 398
- :SBUS:CAN:COUNt:TOTal 399
- :SBUS:CAN:COUNt:UTILization 400
- :SBUS:DISPlay 401
- :SBUS:FLEXray:COUNt:NULL 402
- :SBUS:FLEXray:COUNt:RESet 403
- :SBUS:FLEXray:COUNt:SYNC 404
- :SBUS:FLEXray:COUNt:TOTal 405
- :SBUS:I2S:BASE 406
- :SBUS:IIC:ASIZe 407
- :SBUS:LIN:PARity 408
- :SBUS:M1553:BASE 409
- :SBUS:MODE 410
- :SBUS:SPI:BITorder 411
- :SBUS:SPI:WIDTh 412
- :SBUS:UART:BASE 413
- :SBUS:UART:COUNt:ERRor 414
- :SBUS:UART:COUNt:RESet 415
- :SBUS:UART:COUNt:RXFRames 416
- :SBUS:UART:COUNt:TXFRames 417
- :SBUS:UART:FRAMing 418
- :SYSTem Commands 419
- :SYSTem:DATE 420
- :SYSTem:DSP 421
- :SYSTem:ERRor 422
- :SYSTem:LOCK 423
- :SYSTem:PRECision 424
- :SYSTem:PROTection:LOCK 425
- :SYSTem:SETup 426
- :SYSTem:TIME 428
- :TIMebase Commands 429
- :TIMebase:MODE 431
- :TIMebase:POSition 432
- :TIMebase:RANGe 433
- :TIMebase:REFerence 434
- :TIMebase:SCALe 435
- :TIMebase:VERNier 436
- :TIMebase:WINDow:POSition 437
- :TIMebase:WINDow:RANGe 438
- :TIMebase:WINDow:SCALe 439
- :TRIGger Commands 440
- General :TRIGger Commands 443
- :TRIGger:HFReject 444
- :TRIGger:HOLDoff 445
- :TRIGger:LFIFty 446
- :TRIGger:MODE 447
- :TRIGger:NREJect 448
- :TRIGger:PATTern 449
- :TRIGger:SWEep 451
- :TRIGger:CAN Commands 452
- :TRIGger:CAN:PATTern:DATA 454
- :TRIGger:CAN:PATTern:ID 456
- :TRIGger:CAN:PATTern:ID:MODE 457
- :TRIGger:CAN:SAMPlepoint 458
- :TRIGger:CAN:SIGNal:BAUDrate 459
- :TRIGger:CAN:SOURce 461
- :TRIGger:CAN:TRIGger 462
- :TRIGger:DURation Commands 464
- :TRIGger:DURation:GREaterthan 465
- :TRIGger:DURation:LESSthan 466
- :TRIGger:DURation:PATTern 467
- :TRIGger:DURation:QUALifier 468
- :TRIGger:DURation:RANGe 469
- :TRIGger:EBURst Commands 470
- :TRIGger:EBURst:COUNt 471
- :TRIGger:EBURst:IDLE 472
- :TRIGger:EBURst:SLOPe 473
- :TRIGger[:EDGE] Commands 474
- :TRIGger[:EDGE]:COUPling 475
- :TRIGger[:EDGE]:LEVel 476
- :TRIGger[:EDGE]:REJect 477
- :TRIGger[:EDGE]:SLOPe 478
- :TRIGger[:EDGE]:SOURce 479
- :TRIGger:FLEXray Commands 480
- :TRIGger:FLEXray:AUTosetup 481
- :TRIGger:FLEXray:BAUDrate 482
- :TRIGger:FLEXray:CHANnel 483
- :TRIGger:FLEXray:ERRor:TYPE 484
- :TRIGger:FLEXray:EVENt:TYPE 485
- :TRIGger:FLEXray:FRAMe:CCBase 486
- :TRIGger:FLEXray:FRAMe:ID 488
- :TRIGger:FLEXray:FRAMe:TYPE 489
- :TRIGger:FLEXray:SOURce 490
- :TRIGger:FLEXray:TRIGger 491
- :TRIGger:GLITch Commands 492
- :TRIGger:GLITch:GREaterthan 493
- :TRIGger:GLITch:LESSthan 494
- :TRIGger:GLITch:LEVel 495
- :TRIGger:GLITch:POLarity 496
- :TRIGger:GLITch:QUALifier 497
- :TRIGger:GLITch:RANGe 498
- :TRIGger:GLITch:SOURce 499
- :TRIGger:I2S Commands 500
- :TRIGger:I2S:ALIGnment 502
- :TRIGger:I2S:AUDio 503
- :TRIGger:I2S:CLOCk:SLOPe 504
- :TRIGger:I2S:PATTern:DATA 505
- :TRIGger:I2S:PATTern:FORMat 507
- :TRIGger:I2S:RANGe 508
- :TRIGger:I2S:RWIDth 510
- :TRIGger:I2S:SOURce:CLOCk 511
- :TRIGger:I2S:SOURce:DATA 512
- :TRIGger:I2S:SOURce:WSELect 513
- :TRIGger:I2S:TRIGger 514
- :TRIGger:I2S:TWIDth 516
- :TRIGger:I2S:WSLow 517
- :TRIGger:IIC Commands 518
- :TRIGger:IIC:PATTern:ADDRess 519
- :TRIGger:IIC:PATTern:DATA 520
- :TRIGger:IIC:PATTern:DATa2 521
- :TRIGger:IIC[:SOURce]:CLOCk 522
- :TRIGger:IIC[:SOURce]:DATA 523
- :TRIGger:IIC:TRIGger[:TYPE] 525
- :TRIGger:LIN Commands 527
- :TRIGger:LIN:ID 529
- :TRIGger:LIN:PATTern:DATA 530
- :TRIGger:LIN:PATTern:FORMat 533
- :TRIGger:LIN:SAMPlepoint 534
- :TRIGger:LIN:SIGNal:BAUDrate 535
- :TRIGger:LIN:SOURce 536
- :TRIGger:LIN:STANdard 537
- :TRIGger:LIN:SYNCbreak 538
- :TRIGger:LIN:TRIGger 539
- :TRIGger:M1553 Commands 540
- :TRIGger:M1553:AUTosetup 541
- :TRIGger:M1553:PATTern:DATA 542
- :TRIGger:M1553:RTA 543
- :TRIGger:M1553:SOURce:LOWer 544
- :TRIGger:M1553:SOURce:UPPer 545
- :TRIGger:M1553:TYPE 546
- :TRIGger:SEQuence Commands 547
- :TRIGger:SEQuence:COUNt 548
- :TRIGger:SEQuence:EDGE 549
- :TRIGger:SEQuence:FIND 550
- :TRIGger:SEQuence:PATTern 551
- :TRIGger:SEQuence:RESet 552
- :TRIGger:SEQuence:TIMer 553
- :TRIGger:SEQuence:TRIGger 554
- :TRIGger:SPI Commands 555
- :TRIGger:SPI:CLOCk:SLOPe 556
- :TRIGger:SPI:CLOCk:TIMeout 557
- :TRIGger:SPI:FRAMing 558
- :TRIGger:SPI:PATTern:DATA 559
- :TRIGger:SPI:PATTern:WIDTh 560
- :TRIGger:SPI:SOURce:CLOCk 561
- :TRIGger:SPI:SOURce:DATA 562
- :TRIGger:SPI:SOURce:FRAMe 563
- :TRIGger:TV Commands 564
- :TRIGger:TV:LINE 565
- :TRIGger:TV:MODE 566
- :TRIGger:TV:POLarity 567
- :TRIGger:TV:SOURce 568
- :TRIGger:TV:STANdard 569
- :TRIGger:UART Commands 570
- :TRIGger:UART:BASE 572
- :TRIGger:UART:BAUDrate 573
- :TRIGger:UART:BITorder 574
- :TRIGger:UART:BURSt 575
- :TRIGger:UART:DATA 576
- :TRIGger:UART:IDLE 577
- :TRIGger:UART:PARity 578
- :TRIGger:UART:POLarity 579
- :TRIGger:UART:QUALifier 580
- :TRIGger:UART:SOURce:RX 581
- :TRIGger:UART:SOURce:TX 582
- :TRIGger:UART:TYPE 583
- :TRIGger:UART:WIDTh 584
- :TRIGger:USB Commands 585
- :TRIGger:USB:SOURce:DMINus 586
- :TRIGger:USB:SOURce:DPLus 587
- :TRIGger:USB:SPEed 588
- :TRIGger:USB:TRIGger 589
- :WAVeform Commands 590
- :WAVeform:BYTeorder 597
- :WAVeform:COUNt 598
- :WAVeform:DATA 599
- :WAVeform:FORMat 601
- :WAVeform:POINts 602
- :WAVeform:POINts:MODE 604
- :WAVeform:PREamble 606
- #Vsteps = 607
- :WAVeform:SEGMented:COUNt 609
- :WAVeform:SEGMented:TTAG 610
- :WAVeform:SOURce 611
- :WAVeform:SOURce:SUBSource 615
- :WAVeform:TYPE 616
- :WAVeform:UNSigned 617
- :WAVeform:VIEW 618
- :WAVeform:XINCrement 619
- :WAVeform:XORigin 620
- :WAVeform:XREFerence 621
- :WAVeform:YINCrement 622
- :WAVeform:YORigin 623
- :WAVeform:YREFerence 624
- Commands A-Z 625
- Commands A-Z 6 627
- Commands" on page 750) 657
- Discontinued 661
- Parameters 661
- :CHANnel:LABel 662
- :CHANnel2:SKEW 663
- :CHANnel<n>:INPut 664
- :CHANnel<n>:PMODe 665
- :DISPlay:CONNect 666
- Command Syntax 667
- :EXTernal:INPut 668
- :EXTernal:PMODe 669
- :FUNCtion:SOURce 670
- :FUNCtion:VIEW 671
- :HARDcopy:DESTination 672
- :HARDcopy:DEVice 673
- :HARDcopy:FILename 674
- :HARDcopy:FORMat 675
- :HARDcopy:GRAYscale 676
- :HARDcopy:IGColors 677
- :HARDcopy:PDRiver 678
- :MEASure:LOWer 679
- :MEASure:SCRatch 680
- :MEASure:TDELta 681
- :MEASure:THResholds 682
- :MEASure:TMAX 683
- :MEASure:TMIN 684
- :MEASure:TSTArt 685
- :MEASure:TSTOp 686
- :MEASure:TVOLt 687
- :MEASure:UPPer 689
- :MEASure:VDELta 690
- :MEASure:VSTArt 691
- :MEASure:VSTOp 692
- :MTESt:AMASk:{SAVE 693
- :MTESt:AVERage 694
- :MTESt:AVERage:COUNt 695
- :MTESt:LOAD 696
- :MTESt:RUMode 697
- :MTESt:RUMode:SOFailure 698
- :MTESt:{STARt 699
- :MTESt:TRIGger:SOURce 700
- DISK invalid 702
- PCL invalid 702
- Old Print Option: Is Now: 702
- :TIMebase:DELay 703
- :TRIGger:CAN:ACKNowledge 704
- <value> ::= LIN 705
- :TRIGger:TV:TVMode 706
- Error Messages 707
- Error Messages 8 709
- Status Reporting 715
- Status Reporting 9 717
- Status Byte Register (STB) 721
- Trigger Event Register (TER) 724
- Output Queue 725
- Message Queue 726
- Error Queue 729
- Status Condition Register 731
- Arm Event Register (AER) 732
- Event Condition Register 735
- Clearing Registers and Queues 737
- Synchronizing Acquisitions 739
- Set Up the Oscilloscope 740
- Acquire a Waveform 740
- Retrieve Results 740
- Blocking Synchronization 741
- Synchronizing Acquisitions 10 743
- Command Classifications 750 749
- Query Return Values 772 749
- Command Classifications 750
- ":DISPLAY:LABEL ON" 751
- Program Message 751
- Instruction Header 751
- Separator 751
- Program Data 751
- Simple Command Headers 753
- Compound Command Headers 753
- Common Command Headers 754
- Program Data Syntax Rules 754
- Command Tree 755
- Duplicate Mnemonics 769
- Query Return Values 772
- Programming Examples 775
- VISA COM Examples 776
- Programming Examples 12 777
- " + _ 783
- VISA COM Example in C# 786
- VISA Examples 809
- VISA Example in Visual Basic 818
- VISA Example in C# 828
- SICL Examples 855
- SICL Example in Visual Basic 864
- Numerics 873
- , 251, 254 877
- function, 251, 254 879
Manuais e produtos relacionados com Multímetros Agilent Technologies InfiniiVision 5000 Series
Multímetros Agilent Technologies 34401A Especificações
(482 páginas)
(482 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais