Agilent-technologies E1300B Manual do Utilizador Página 160
- Página / 244
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
STATus The STATus subsystem commands access the condition, event, and enable
registers in the Operation Status group and the Questionable Data group.
Subsystem Syntax STATus
:OPERation
:CONDition?
:ENABle < event>
:ENABle?
[:EVENt]?
:PRESet
:QUEStionable
:CONDition?
:ENABle < event>
:ENABle?
[:EVENt]?
:OPERation
:CONDition?
STATus:OPER:COND? returns the state of the condition register in the
Operation Status group. The state represents conditions which are part of an
instrument’s operation.
Comments • Bit 8 in the register is used by the System Instrument (Command
Module) to indicate when an interrupt set up by the DIAG:INTerrupt
commands has been acknowledged.
• Reading the condition register does not change the setting of bit 8. Bit 8
is cleared by the DIAG:INT:RESP? command.
• Related Commands: STAT:OPER:ENABle, STAT:OPER:EVENt?
Example Reading the contents of the condition register
STAT:OPER:COND? query register
enter statement
:OPERation:ENABle
<event>
STATus:OPER:ENABle < event> sets an enable mask to allow events
monitored by the condition register and recorded in the event register, to send a
summary bit to the Status Byte register (bit 7).
Parameters Parameter
Name
Parameter
Type
Range of
Values
Default
Units
event numeric 256 none
Comments • Bit 8 in the condition register is used by the system instrument
(Command Module) to indicate when an interrupt set up by the
DIAG:INTerrupt commands has been acknowledged.
STATus :OPERation :CONDition?
7-32 System Instrument Command Reference
- 75000 SERIES B 1
- Mainframes 1
- E1300B and E1301B 1
- Multimeter User’s Manual 6
- About this Manual 8
- Table of Contents 9
- 6 - Table of Contents 14
- Getting Started 15
- Instrument 17
- Definition 17
- Introductory 18
- Programming 18
- Examples 18
- 1-6 Getting Started 20
- Using the Front Panel 21
- A 60-Second Menu 22
- Tutorial 22
- Using the System 23
- Instrument Menu 23
- How to Reset the System 24
- Using the Other 25
- Instrument Menus 25
- How to Open/Close Channels 26
- How to Scan Channels 26
- How to Select Monitor Mode 27
- Executing 29
- Menu Keys 30
- Display Control & 30
- Editing Keys 30
- Instrument Control 31
- Other Keys 31
- In Case of Difficulty 32
- System Instrument Menu 34
- Switchbox Menu 36
- Using the Front Panel 2-17 37
- Scanning Voltmeter Menu 38
- Using the Front Panel 2-23 43
- Counter Menu 46
- 2-28 Using the Front Panel 48
- Chapter 3 49
- Terminal Interface 50
- Features 50
- General Key 62
- Descriptions 62
- Using Supported 64
- Terminals 64
- Using Other 67
- What “Not Supported” 68
- Testing Terminals for 68
- Compatibility 68
- Using a Terminal 69
- Without Menus 69
- Using the Mainframe 89
- Mainframe Data 94
- Non-Volatile User 95
- Downloading Device Drivers 99
- GPIB bus 100
- Configuration 101
- Download Program 102
- Downloading 104
- Drivers in MS-DOS 104
- Systems with 105
- Drivers in GPIB 105
- Systems with BASIC 106
- Multiple Drivers 107
- Checking Driver 107
- Manually 108
- Downloading a 108
- Driverdown manual 108
- Manually Downloading 109
- Over GPIB 109
- Over RS-232 109
- Chapter 6 115
- Status System 116
- Structure 116
- The Status Byte 117
- Register 117
- Reading the Status 118
- Byte Register 118
- Standard Event Status 120
- Unmasking Standard 120
- Event Status Bits 120
- Reading the 122
- Condition Register 122
- Unmasking the 122
- Operation Event 122
- Register Bits 122
- Clearing the Operation 123
- Event Register Bits 123
- Using the Operation 123
- Status Group Registers 123
- Interrupting an 124
- External Computer 124
- Synchronizing an 126
- Chapter 7 129
- SCPI Command 132
- Reference 132
- :COMMunicate 135
- :SERial[0][:OWNer] 135
- :SERial[0][:OWNer]? 136
- :SERial[n]:STORe 136
- :DOWNload:CHECked 137
- [:MADDress] 137
- :SADDress 139
- :DOWNload 141
- :DRIVer:LOAD 145
- < driver_block> 145
- :DRIVer :LOAD: 145
- :OPERation 160
- :CONDition? 160
- :OPERation:ENABle 160
- <event> 160
- :SERial[n] :CONTrol 165
- :CONFigure 182
- :DLADdress? 182
- ADDR 0" 184
- :HIERarchy? 185
- :HIERarchy:ALL? 186
- :INFormation? 186
- GPIB Message 200
- Device Clear (DCL) or 201
- Selected Device Clear 201
- Command Quick 203
- SCPI Commands Quick Reference 204
- Command Description 204
- System Instrument 204
- Specifications 209
- SCPI Conformance 211
- Information 211
- A-4 Specifications 212
- Specifications A-5 213
- A-6 Specifications 214
- Specifications A-7 215
- D/A Converter 216
- Commands 216
- Specifications A-9 217
- Specifications A-11 219
- A-12 Specifications 220
- Error Messages 221
- Error Messages B-3 223
- Error Messages and Causes 223
- Code Message Cause 223
- B-4 Error Messages 224
- Start-up Error 225
- Messages 225
- B-6 Error Messages 226
- Connecting and Configuring a 227
- Display Terminal 227
- Agilent 24542H 228
- Configuring a 229
- Terminal for the 229
- Mainframe 229
- Configuring the 230
- Mainframe with 230
- Appendix D 233
- Sending Binary 234
- Data Over RS-232 234
Manuais e produtos relacionados com Hardware Agilent-technologies E1300B
(20 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais