Agilent Technologies 4287A-03 Manual de Instruções Página 275
- Página / 344
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 12 275
Specifications and Supplemental Performance Characteristics
General Characteristics
12. Specifications and
Supplemental Performance
Characteristics
General Characteristics
Environment conditions
Operating Condition
Non-Operating Storage Condition
Temperature 5 °C to 40 °C
Humidity (at wet bulb
temperature ≤ 29 °C, without
condensation)
Flexible disk drive
non-operating condition
20 % to 80 % RH
Flexible disk drive
operating condition
15 % to 90 % RH
Altitude 0 to 2,000 m (0 to 6,561 feet)
Vibration 0.5 G maximum, 5 Hz to 500 Hz
Warm-up time 30 minutes
Temperature − 20°C to + 60°C
Humidity (at wet bulb
temperature ≤ 45 °C, without
condensation)
15% to 90% RH
Altitude 0 to 4,572 m (0 to 15,000 feet)
Vibration 1 G maximum, 5 Hz to 500 Hz
- Operation Manual 1
- Manual Printing History 2
- Safety Summary 3
- Safety Symbols 4
- Certification 4
- Warranty 5
- Limitation of Warranty 5
- Exclusive Remedies 5
- Assistance 6
- Typeface Conventions 6
- 4287A Documentation Map 7
- Software Installed 7
- Contents 10
- 1. How to Use This 15
- Operation Manual 15
- 2 Installation Guide 17
- Incoming Inspection 18
- Environmental Requirements 20
- Connecting Mouse and Keyboard 29
- LAN Connection 30
- Connecting the Test Head 31
- Agilent 4287A 33
- Preparation for Power Supply 35
- 36 Chapter 2 36
- Installation Guide 36
- Blown fuse 37
- Turning the Power ON and OFF 38
- Initial Registration of 4287A 40
- I accept this agreement 41
- Windows always 42
- Finish button to finish the 42
- Setting the Internal Clock 43
- Selection of Test Fixture 45
- Instructions for Cleaning 46
- 3 Learning Basic Operations 49
- What You Must Keep on Hand 50
- Preparation for Measurement 52
- Turning ON the power 53
- Presetting the 4287A 54
- Executing short calibration 58
- Cal/Compen for a Fixture 59
- Next> button 59
- Executing open calibration 61
- Executing load calibration 63
- Connection of Test Fixture 65
- Executing short compensation 66
- Executing open compensation 67
- Finish button 68
- POINT No.[ ] key 69
- POINT 4 in this case) 69
- SETUP MEAS 70
- PRMTRS key 70
- PRMTR-1 [ ] in this case) 70
- Ls in this case) 70
- (list measurement) 71
- 72 Chapter 3 72
- Learning Basic Operations 72
- 4 Function Overview 73
- 1. Stand-by switch ( ) 74
- 3. Color LCD display 75
- 7. Entry block (ENTRY) 76
- [×1] key 77
- [Alt] key. When a 77
- *1. Unshielded Twisted Pair 80
- 11. Serial number plate 81
- 12. Option plate 81
- 13. Reserved ports (Reserved) 81
- Chapter 4 83 83
- 4. Function Overview 83
- [0] to [9]) to select the 84
- [0] to [9]) of the 85
- ↑], [↓], [←] and [→]) of the 85
- List measurement display 89
- Calibration kit setup display 93
- 9. DC standard value 94
- Bin sorting setup display 97
- 100 Chapter 4 100
- Function Overview 100
- 4287A Key Operation Overview 100
- How to Preset the 4287A 102
- [Setup View] key 103
- How to add measurement points 105
- [0] to [9] and 108
- [9]) and [×1]) sequentially 109
- Setting up dc resistance (R 113
- ) measurement 113
- 11 4 Chapter 5 114
- Test Fixture 120
- Close button 123
- Dedicated Test Fixture 135
- How to Define Calibration Kit 145
- Fixtures 149
- Compensation 151
- 154 Chapter 6 154
- Calibration and Compensation 154
- 7. Executing Measurements 155
- Connecting the DUT 156
- Measurement Display 160
- Hiding the Screen Display 166
- 170 Chapter 7 170
- 8. Sorting According to 171
- Measurement Results 171
- Overview of BIN Sort Function 172
- Concept of setting 4287A BINs 174
- Chapter 8 175 175
- 176 Chapter 8 176
- Setting Measurement Point 177
- Setting Measurement Parameter 179
- 180 Chapter 8 180
- Setting limit mode 181
- Setting reference value 182
- Setting BIN Range 183
- Setting lower limit value 184
- Selecting BIN range mode 185
- Setting BIN On and Off 186
- 2. Edit” on the menu bar 187
- Measurement 188
- Bin Count Function 190
- Table 8-2 Sorting conditions 192
- OUT OF GOOD BINS setting 202
- START LOGGING key 208
- 212 Chapter 9 212
- Saving Setting Status 214
- Saving Screen Displays 216
- 224 Chapter 10 224
- Management Facilities 225
- [Delete]. (Not possible) 226
- [×1], , or 227
- [Cancel] 227
- [Alt] key 227
- Configuring the Network 228
- Setting IP address 229
- Specifying computer name 231
- OK button 232
- OK button (2 in Figure 11-6) 232
- OK button (2 in Figure 11-5) 232
- Yes button to 232
- BEEP DONE [ON] ON 233
- BEEP DONE [OFF] OFF 233
- (Pass or Fail) 234
- Locking the keyboard 236
- Locking the mouse 237
- BACK LIGHT [ON] 239
- System Recovery 240
- 250 Chapter 11 250
- Performance Characteristics 251
- Measurement parameters 253
- Measurement range 253
- Source characteristics 253
- 254 Chapter 12 254
- Measurement accuracy 255
- 256 Chapter 12 256
- Definition of Each Parameter 256
- Oscillator level < −33 258
- 260 Chapter 12 260
- 264 Chapter 12 264
- Measurement Support Functions 270
- 272 Chapter 12 272
- Handler Interface 272
- Rear panel connectors 273
- 274 Chapter 12 274
- General Characteristics 275
- 276 Chapter 12 276
- Other Specifications 276
- 278 Chapter 12 278
- Furnished accessories 280
- DC resistance 281
- Furnished devices 281
- 282 Chapter 12 282
- A Manual Changes 283
- Manual Changes 284
- Change 7 285
- Change 6 285
- Change 5 287
- Change 4 288
- Miscellaneous Changes 291
- Change 3 293
- Change 2 293
- Change 1 293
- 294 Appendix A 294
- Other Important Differences 297
- Table B-3 Calibration 299
- 302 Appendix B 302
- 304 Appendix B 304
- 306 Appendix B 306
- 308 Appendix B 308
- Errors Occur 311
- Internal Data on a Printer 313
- Printer Support 314
- Procedure for Printing 316
- 3. Setting paper orientation 317
- F Error Messages 319
- Order of Error Number 320
- 328 Appendix F 328
- Error Messages 328
- Undefined header 328
- G Information on Maintenance 329
- Cleaning this Instrument 330
- Regular Calibration, etc 333
- 334 Appendix G 334
- Information on Maintenance 334
- Calibration, etc 334
- Index 335 335
- Index Index 335
- 336 Index 336
- Index 337 337
- 338 Index 338
- Index 339 339
- 340 Index 340
- Index 341 341
- 342 Index 342
- Index 343 343
- 344 Index 344
Manuais e produtos relacionados com Relógios de parede Agilent Technologies 4287A-03
(168 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.188 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais