Agilent Technologies 4287A-03 Manual de Instruções Página 181
- Página / 344
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 8 181
Sorting According to Measurement Results
Setting Limit Mode and Reference Value
8. Sorting According to
Measurement Results
Setting Limit Mode and Reference Value
Setting limit mode
This procedure determines the format used to set the upper and lower limits of the
measurement values for BIN sorting.
Step 1. Click with the mouse in the BIN limit setting mode cell in the sorting condition to be set
(one of conditions 1 to 4).
Step 2. Click the down arrow () at the right edge of the cell.
Step 3. Click the desired limit mode from the drop-down list box to select it (Figure 8-3).
Figure 8-7 Selection of limit mode for sorting condition 1
Limit mode Definition
ABS Absolute mode. The limits of each BIN
are set as absolute values. If you select
this mode, you do not need to set the
reference value (nominal).
PCNT Percentage mode. The limit value of each
BIN is set as a percentage of the reference
value.
DEV Deviation mode. The limit value of each
BIN is set as a difference with respect to
the reference value. Use the same unit as
that of the set measurement parameter.
- Operation Manual 1
- Manual Printing History 2
- Safety Summary 3
- Safety Symbols 4
- Certification 4
- Warranty 5
- Limitation of Warranty 5
- Exclusive Remedies 5
- Assistance 6
- Typeface Conventions 6
- 4287A Documentation Map 7
- Software Installed 7
- Contents 10
- 1. How to Use This 15
- Operation Manual 15
- 2 Installation Guide 17
- Incoming Inspection 18
- Environmental Requirements 20
- Connecting Mouse and Keyboard 29
- LAN Connection 30
- Connecting the Test Head 31
- Agilent 4287A 33
- Preparation for Power Supply 35
- 36 Chapter 2 36
- Installation Guide 36
- Blown fuse 37
- Turning the Power ON and OFF 38
- Initial Registration of 4287A 40
- I accept this agreement 41
- Windows always 42
- Finish button to finish the 42
- Setting the Internal Clock 43
- Selection of Test Fixture 45
- Instructions for Cleaning 46
- 3 Learning Basic Operations 49
- What You Must Keep on Hand 50
- Preparation for Measurement 52
- Turning ON the power 53
- Presetting the 4287A 54
- Executing short calibration 58
- Cal/Compen for a Fixture 59
- Next> button 59
- Executing open calibration 61
- Executing load calibration 63
- Connection of Test Fixture 65
- Executing short compensation 66
- Executing open compensation 67
- Finish button 68
- POINT No.[ ] key 69
- POINT 4 in this case) 69
- SETUP MEAS 70
- PRMTRS key 70
- PRMTR-1 [ ] in this case) 70
- Ls in this case) 70
- (list measurement) 71
- 72 Chapter 3 72
- Learning Basic Operations 72
- 4 Function Overview 73
- 1. Stand-by switch ( ) 74
- 3. Color LCD display 75
- 7. Entry block (ENTRY) 76
- [×1] key 77
- [Alt] key. When a 77
- *1. Unshielded Twisted Pair 80
- 11. Serial number plate 81
- 12. Option plate 81
- 13. Reserved ports (Reserved) 81
- Chapter 4 83 83
- 4. Function Overview 83
- [0] to [9]) to select the 84
- [0] to [9]) of the 85
- ↑], [↓], [←] and [→]) of the 85
- List measurement display 89
- Calibration kit setup display 93
- 9. DC standard value 94
- Bin sorting setup display 97
- 100 Chapter 4 100
- Function Overview 100
- 4287A Key Operation Overview 100
- How to Preset the 4287A 102
- [Setup View] key 103
- How to add measurement points 105
- [0] to [9] and 108
- [9]) and [×1]) sequentially 109
- Setting up dc resistance (R 113
- ) measurement 113
- 11 4 Chapter 5 114
- Test Fixture 120
- Close button 123
- Dedicated Test Fixture 135
- How to Define Calibration Kit 145
- Fixtures 149
- Compensation 151
- 154 Chapter 6 154
- Calibration and Compensation 154
- 7. Executing Measurements 155
- Connecting the DUT 156
- Measurement Display 160
- Hiding the Screen Display 166
- 170 Chapter 7 170
- 8. Sorting According to 171
- Measurement Results 171
- Overview of BIN Sort Function 172
- Concept of setting 4287A BINs 174
- Chapter 8 175 175
- 176 Chapter 8 176
- Setting Measurement Point 177
- Setting Measurement Parameter 179
- 180 Chapter 8 180
- Setting limit mode 181
- Setting reference value 182
- Setting BIN Range 183
- Setting lower limit value 184
- Selecting BIN range mode 185
- Setting BIN On and Off 186
- 2. Edit” on the menu bar 187
- Measurement 188
- Bin Count Function 190
- Table 8-2 Sorting conditions 192
- OUT OF GOOD BINS setting 202
- START LOGGING key 208
- 212 Chapter 9 212
- Saving Setting Status 214
- Saving Screen Displays 216
- 224 Chapter 10 224
- Management Facilities 225
- [Delete]. (Not possible) 226
- [×1], , or 227
- [Cancel] 227
- [Alt] key 227
- Configuring the Network 228
- Setting IP address 229
- Specifying computer name 231
- OK button 232
- OK button (2 in Figure 11-6) 232
- OK button (2 in Figure 11-5) 232
- Yes button to 232
- BEEP DONE [ON] ON 233
- BEEP DONE [OFF] OFF 233
- (Pass or Fail) 234
- Locking the keyboard 236
- Locking the mouse 237
- BACK LIGHT [ON] 239
- System Recovery 240
- 250 Chapter 11 250
- Performance Characteristics 251
- Measurement parameters 253
- Measurement range 253
- Source characteristics 253
- 254 Chapter 12 254
- Measurement accuracy 255
- 256 Chapter 12 256
- Definition of Each Parameter 256
- Oscillator level < −33 258
- 260 Chapter 12 260
- 264 Chapter 12 264
- Measurement Support Functions 270
- 272 Chapter 12 272
- Handler Interface 272
- Rear panel connectors 273
- 274 Chapter 12 274
- General Characteristics 275
- 276 Chapter 12 276
- Other Specifications 276
- 278 Chapter 12 278
- Furnished accessories 280
- DC resistance 281
- Furnished devices 281
- 282 Chapter 12 282
- A Manual Changes 283
- Manual Changes 284
- Change 7 285
- Change 6 285
- Change 5 287
- Change 4 288
- Miscellaneous Changes 291
- Change 3 293
- Change 2 293
- Change 1 293
- 294 Appendix A 294
- Other Important Differences 297
- Table B-3 Calibration 299
- 302 Appendix B 302
- 304 Appendix B 304
- 306 Appendix B 306
- 308 Appendix B 308
- Errors Occur 311
- Internal Data on a Printer 313
- Printer Support 314
- Procedure for Printing 316
- 3. Setting paper orientation 317
- F Error Messages 319
- Order of Error Number 320
- 328 Appendix F 328
- Error Messages 328
- Undefined header 328
- G Information on Maintenance 329
- Cleaning this Instrument 330
- Regular Calibration, etc 333
- 334 Appendix G 334
- Information on Maintenance 334
- Calibration, etc 334
- Index 335 335
- Index Index 335
- 336 Index 336
- Index 337 337
- 338 Index 338
- Index 339 339
- 340 Index 340
- Index 341 341
- 342 Index 342
- Index 343 343
- 344 Index 344
Manuais e produtos relacionados com Relógios de parede Agilent Technologies 4287A-03
(168 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.120 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais