Agilent Technologies 8000 Series Guia do Utilizador descarregar pdf (Página 107)

Using the Oscilloscope

To recover your Infiniium hard disk

3-62

5 When the Splash screen (Figure 3-43) appears, hold down one of the

control (Ctrl) keys.

Figure 3-43

Infiniium Splash Screen

6 Once the Recovery Screen (Figure 3-44) appears you can release the

control key.



࣭एंऐऐ ऑऌ ऐअऌऔ ࣰࣱ࣭࣬ ऐऀएंंऋࣉ ऑऌ ंऋऑंए ࣰ࣢ࣱࣲ࣭ࣉ ऑऌ ऐंउंऀऑ ࣱࣟ࣬࣬ ࣡࣢ࣦࣳ࣠࣢

1 2 ... 102 103 104 105 106 107 108 109 110 111 112 ... 128 129

Infiniium 1
Infiniium Oscilloscopes 2
In This Book 3
Contents 4
Figure 1-1 9
Setting Up the Oscilloscope 10
To inspect package contents 10
Figure 1-2 10
Ω) or 20:1 (1 kΩ), .25 pf 12
To connect power 16
Table 1-4 18
Power Cords 18
Figure 1-5 21
Attaching the Probe Connector 22
Figure 1-7 23
To connect SMA Cables 25
To connect the digital probe 26
Digital probe lead set 27
Probe Tip Isolation Network 28
40-pin Connector Pinout 29
Figure 1-15 31
To turn on the oscilloscope 32
To turn off the oscilloscope 33
Calibration 34
To clean the oscilloscope 40
Working in Comfort 42
Introduction 43
Mice and Other Input Devices 45
Using the Front Panel 48
Front Panel 49
Horizontal Controls 50
Trigger Controls 50
Vertical Controls 50
To clear the waveform display 54
Channel Key 55
Use this key to turn 55
Digital Channels Key 56
Use this key to turn digital 56
Vertical offset knob— 58
Figure 3-8 59
Delayed again 61
Figure 3-12 63
To use the markers 64
To use the quick measurements 65
Using the Graphical Interface 67
Graphical User Interface 68
Tab Display Area 71
Figure 3-19 76
Figure 3-20 77
1 Click on a menu bar item 78
Figure 3-22 80
Figure 3-23 81
To print the screen 84
To change waveform brightness 85
To turn a channel on or off 86
To adjust the vertical offset 87
...or click on the 88
Click to access the 88
To adjust vertical scaling 89
To access the channel setup 90
To adjust sweep speed 92
To adjust horizontal position 93
Figure 3-36 96
1 Turn on the markers 97
Figure 3-37 98
Using the Oscilloscope 100
Figure 3-38 100
To access the trigger setup 101
To set an edge trigger 102
To set dialog box preferences 103
Figure 3-41 104
Figure 3-42 105
Figure 3-43 107
Figure 3-44 108
To calibrate the touch screen 109
Figure 3-45 110
Figure 4-1 115
Access Methods 116
Figure 4-2 116
Topic Types 118
Figure 4-4 119
3-26, 3-27, 3-42 122

Comentários a estes Manuais

Sem comentários

Agilent Technologies 8000 Series Guia do Utilizador Página 107

Comentários a estes Manuais

Manuais e produtos relacionados com não Agilent Technologies 8000 Series