Agilent Technologies 8753ET Especificações Página 174
- Página / 262
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
6-4
Error Messages
Error Messages in Alphabetical Order
ARGUMENT OUT OF RANGE
Error Number
206
The argument for a programming command is out of the specified range. Refer
to the programmer’s guide for a list of programming commands and argument
ranges.
ASCII: MISSING 'BEGIN' STATEMENT
Error Number
193
The CITIfile you just downloaded over the GPIB or via disk was not properly
organized. The analyzer is unable to read the “BEGIN” statement.
ASCII: MISSING 'CITIFILE' STATEMENT
Error Number
194
The CITIfile you just downloaded over the GPIB or via disk was not properly
organized. The analyzer is unable to read the “CITIFILE” statement.
ASCII: MISSING 'DATA' STATEMENT
Error Number
195
The CITIfile you just downloaded over the GPIB or via disk was not properly
organized. The analyzer is unable to read the “DATA” statement.
ASCII: MISSING 'VAR' STATEMENT
Error Number
196
The CITIfile you just downloaded over the GPIB or via disk was not properly
organized. The analyzer is unable to read the “VAR” statement.
AVERAGING INVALID ON NON-RATIO MEASURE
Error Number
13
You cannot use sweep-to-sweep averaging in single-input measurements.
Sweep-to-sweep averaging is valid only for ratioed measurements (A/R, B/R,
A/B, and S-parameters). You can use other noise reduction techniques, such as
narrower IF bandwidth, for single input measurements.
BAD FREQ FOR HARMONIC OR FREQ OFFSET
Error Number
181
You turned on time domain or recalled a calibration that resulted in start and
stop frequencies that are beyond the allowable limits.
BANDWIDTH LIMIT INVALID: MIN BW > MAX BW
Information
Message
The bandwidth test has a minimum bandwidth greater than the maximum
bandwidth. Change the minimum bandwidth to a frequency less than the
frequency of the maximum bandwidth or change the maximum bandwidth to a
frequency greater than the frequency of the minimum bandwidth
- Reference Guide 1
- Certification 2
- Assistance 2
- Safety Notes 2
- How to Use This Guide 3
- Documentation Map 4
- Contents 5
- 1 8753ES 9
- Definitions 10
- Corrected System Performance 11
- Instrument Specifications 18
- Test Port Output 20
- Table 1-11 Test Port Output 21
- Table 1-12 Test Port Output 22
- Table 1-13 Test Port Output 23
- Test Port Input 24
- Table 1-15 Test Port Input 25
- Table 1-16 Test Port Input 26
- Table 1-17 Test Port Input 27
- Table 1-18 Test Port Input 27
- Table 1-19 Test Port Input 28
- Table 1-20 Test Port Input 29
- General Information 30
- Speed Parameters 36
- Total Time 37
- 2 8753ET 41
- Table 2-5 Test Port Output 48
- Table 2-6 Test Port Output 49
- Table 2-7 Test Port Output 50
- Table 2-9 Test Port Input 52
- Table 2-10 Test Port Input 53
- Table 2-11 Test Port Input 54
- Table 2-12 Test Port Input 54
- Table 2-13 Test Port Input 55
- Table 2-14 Test Port Input 56
- Table 2-15 Test Port Input 57
- 3 Front/Rear Panel 69
- Front Panel Features 70
- Front/Rear Panel 71
- Analyzer Display 73
- , the IF frequency is not 75
- Marker Fctn 77
- MEASURE RESTART 79
- 4 Menu Maps 81
- Figure 4-2 Menu Map for Copy 83
- Figure 4-5 Menu Map for Local 86
- Meas (ET Models Only) 88
- Meas (ES Models Only) 89
- Save/Recall 93
- Scale Ref 94
- Pwr. Loss/Sens 95
- Lists Menu 95
- Enhanced 95
- Response Menu 95
- Seq Spec 97
- Func Menu 97
- SEQUENCE X 97
- FREQUENCY : 98
- Menu Maps 100
- 5 Hardkey/Softkey Reference 101
- Key Reference 102
- Guide Terms and Conventions 103
- Analyzer Functions 104
- --------= 167
- Velocity Factor 167
- Hardkey/Softkey Reference 170
- 6 Error Messages 171
- Error Messages 172
- PHASE LOCK LOST 188
- 7 Options and Accessories 203
- Using This Chapter 204
- Analyzer Options Available 205
- Service and Support Options 206
- Accessories Available 207
- Options and Accessories 208
- Test Configuration Accessories 212
- Keyboard Template 214
- Preset State 216
- Table 8-1 Preset Conditions 217
- Table 8-2 Preset Conditions 224
- Memory Allocation 226
- Storing Data to Disk 230
- Conserving Memory 232
- Using Saved Calibration Sets 232
- Clearing Memory 233
- The CITIfile Data Format 237
- CITIfile Examples 239
- CITIfile Keywords 242
- Useful Calculations 245
- Uncertainties 249
- Introduction 250
- Sources of Measurement Errors 251
- Sources of Random Errors 252
- (−60/20) 254
- (0.013/40) 255
- Forward Reflection Uncertainty 256
- Reverse Reflection Uncertainty 258
Manuais e produtos relacionados com Redes Agilent Technologies 8753ET
Redes Agilent Technologies 8753ET Guia do Utilizador
(546 páginas)
(546 páginas)
(21 páginas)
Redes Agilent Technologies 8753ES Guia do Utilizador
(245 páginas)
(245 páginas)
Redes Agilent Technologies N9360A Manual do Utilizador
(354 páginas)
(354 páginas)
Redes Agilent Technologies 81640A Guia do Utilizador
(114 páginas)
(114 páginas)
Redes Agilent Technologies E6474A Manual de Serviço
(52 páginas)
(52 páginas)
Redes Agilent Technologies J3972A Guia do Utilizador
(551 páginas)
(551 páginas)
Redes Agilent Technologies 81689A Guia do Utilizador
(117 páginas)
(117 páginas)
Redes Agilent Technologies E5805A Guia de Instalação
(47 páginas)
(47 páginas)
Redes Agilent Technologies 8922S Especificações
(204 páginas)
(204 páginas)
Redes Agilent Technologies E6474A Guia do Utilizador
(184 páginas)
(184 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais