Agilent Technologies 8753ET Especificações Página 140
- Página / 262
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
5-40
Hardkey/Softkey Reference
Analyzer Functions
leads to the series of menus used to perform a
high-accuracy two-port calibration without an
S-parameter test set. This calibration procedure
effectively removes directivity, source match, load match,
isolation, reflection tracking, and transmission tracking
errors in one direction only. Isolation correction can be
omitted for measurements of devices with limited dynamic
range. (The device under test must be manually reversed
between sweeps to accomplish measurement of both input
and output responses.) The required standards are a
short, an open, a thru, and an impedance-matched load.
This mode does not measure each sweep, but corrects each
point with the data currently in the power meter
correction table.
provides a tabular listing on the analyzer display of the
key parameters for both channels. The screen menu is
presented to allow hard copy listings and access new pages
of the table. Four pages of information are supplied. These
pages list operating parameters, marker parameters, and
system parameters that relate to control of peripheral
devices rather than selection of measurement parameters.
defines the standard type as an open, used for calibrating
reflection measurements. Opens are assigned a terminal
impedance of infinite Ωs, but delay and loss offsets may
still be added.
for cal kits with different models for male and female test
port standards, this selects the open model for a female
test port. Note that the sex of a calibration standard
always refers to the test port.
for cal kits with different models for male and female test
port standards, this selects the open model for a male test
port. Note that the sex of a calibration standard always
refers to the test port.
gets data from an GPIB device set to the address at which
the analyzer expects to find a power meter. The data is
stored in a title string. The analyzer must be in system
controller or pass control mode.
is located in the ECal confidence and ECal service menus.
In ES models you can display the S11, S22, S21, or S12
ECal module factory response and the actual
measurement response. In ET models, you can display the
TRN or RFL responses.
while creating a sequence, this softkey will insert a
command that selects the single bit (0 to 4) that a
sequence will be looking for from the GPIO bus.
ONE-PATH 2-PORT
ONE SWEEP
OP PARMS (MKRS etc)
OPEN
OPEN (F)
OPEN (M)
P MTR/GPIB TO TITLE
PARAMETER [S11]
PARALL IN BIT NUMBER
- Reference Guide 1
- Certification 2
- Assistance 2
- Safety Notes 2
- How to Use This Guide 3
- Documentation Map 4
- Contents 5
- 1 8753ES 9
- Definitions 10
- Corrected System Performance 11
- Instrument Specifications 18
- Test Port Output 20
- Table 1-11 Test Port Output 21
- Table 1-12 Test Port Output 22
- Table 1-13 Test Port Output 23
- Test Port Input 24
- Table 1-15 Test Port Input 25
- Table 1-16 Test Port Input 26
- Table 1-17 Test Port Input 27
- Table 1-18 Test Port Input 27
- Table 1-19 Test Port Input 28
- Table 1-20 Test Port Input 29
- General Information 30
- Speed Parameters 36
- Total Time 37
- 2 8753ET 41
- Table 2-5 Test Port Output 48
- Table 2-6 Test Port Output 49
- Table 2-7 Test Port Output 50
- Table 2-9 Test Port Input 52
- Table 2-10 Test Port Input 53
- Table 2-11 Test Port Input 54
- Table 2-12 Test Port Input 54
- Table 2-13 Test Port Input 55
- Table 2-14 Test Port Input 56
- Table 2-15 Test Port Input 57
- 3 Front/Rear Panel 69
- Front Panel Features 70
- Front/Rear Panel 71
- Analyzer Display 73
- , the IF frequency is not 75
- Marker Fctn 77
- MEASURE RESTART 79
- 4 Menu Maps 81
- Figure 4-2 Menu Map for Copy 83
- Figure 4-5 Menu Map for Local 86
- Meas (ET Models Only) 88
- Meas (ES Models Only) 89
- Save/Recall 93
- Scale Ref 94
- Pwr. Loss/Sens 95
- Lists Menu 95
- Enhanced 95
- Response Menu 95
- Seq Spec 97
- Func Menu 97
- SEQUENCE X 97
- FREQUENCY : 98
- Menu Maps 100
- 5 Hardkey/Softkey Reference 101
- Key Reference 102
- Guide Terms and Conventions 103
- Analyzer Functions 104
- --------= 167
- Velocity Factor 167
- Hardkey/Softkey Reference 170
- 6 Error Messages 171
- Error Messages 172
- PHASE LOCK LOST 188
- 7 Options and Accessories 203
- Using This Chapter 204
- Analyzer Options Available 205
- Service and Support Options 206
- Accessories Available 207
- Options and Accessories 208
- Test Configuration Accessories 212
- Keyboard Template 214
- Preset State 216
- Table 8-1 Preset Conditions 217
- Table 8-2 Preset Conditions 224
- Memory Allocation 226
- Storing Data to Disk 230
- Conserving Memory 232
- Using Saved Calibration Sets 232
- Clearing Memory 233
- The CITIfile Data Format 237
- CITIfile Examples 239
- CITIfile Keywords 242
- Useful Calculations 245
- Uncertainties 249
- Introduction 250
- Sources of Measurement Errors 251
- Sources of Random Errors 252
- (−60/20) 254
- (0.013/40) 255
- Forward Reflection Uncertainty 256
- Reverse Reflection Uncertainty 258
Manuais e produtos relacionados com Redes Agilent Technologies 8753ET
Redes Agilent Technologies 8753ET Guia do Utilizador
(546 páginas)
(546 páginas)
(21 páginas)
Redes Agilent Technologies 8753ES Guia do Utilizador
(245 páginas)
(245 páginas)
Redes Agilent Technologies N9360A Manual do Utilizador
(354 páginas)
(354 páginas)
Redes Agilent Technologies 81640A Guia do Utilizador
(114 páginas)
(114 páginas)
Redes Agilent Technologies E6474A Manual de Serviço
(52 páginas)
(52 páginas)
Redes Agilent Technologies J3972A Guia do Utilizador
(551 páginas)
(551 páginas)
Redes Agilent Technologies 81689A Guia do Utilizador
(117 páginas)
(117 páginas)
Redes Agilent Technologies E5805A Guia de Instalação
(47 páginas)
(47 páginas)
Redes Agilent Technologies 8922S Especificações
(204 páginas)
(204 páginas)
Redes Agilent Technologies E6474A Guia do Utilizador
(184 páginas)
(184 páginas)
Sony MDR-EX57LP Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Audio Sony MDR-EX57LP.
Wir stellen 1 PDF-Handbücher Sony MDR-EX57LP zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comentários a estes Manuais