Agilent Technologies N9340A Guia do Utilizador Página 161
- Página / 179
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
SCPI Command Reference 6
N9340A User’s Guide 155
TRIGer Subsystem
Trigger subsystem is only valid when the analyzer
is in zero span.
External Trigger Slope
:TRIGer[:SEQuence]:EXTernal:SLOPe
POSitive|NEGative
:TRIGer[:SEQuence]:EXTernal:SLOPe?
The external trigger signal must be a TTL signal at
0 V to 5 V. This function controls the trigger
polarity (for positive or negative- going signals).
Trigg er Source
:TRIGer[:SEQuence]:SOURce
IMMediate|VIDeo|EXTernal
:TRIGer[:SEQuence]:SOURce?
This command sets the source (or type) of
triggering used to start a measurement.
• Immediate is free- run triggering.
• Video triggers on the video signal level.
• External allows you to connect an external
trigger source.
Video Trigger Level Amplitude
:TRIGer[:SEQuence]:VIDeo:LEVel <ampl>
:TRIGer[:SEQuence]:VIDeo:LEVe?
This command specifies the video trigger level.
*RST state: Positive
*RST state: Immediate (free-run triggering)
Key access: [Span] > {Trigger}
*RST Value: 0.00 dBm
Key Access: [Span] > {Trigger}
- User’s Guide 1
- 2
- Contents 3
- 5 Key Reference 4
- 6 SCPI Command Reference 4
- 7Error Messages 5
- 8 Menu Map 5
- Documentation Conventions: 5
- Overview 7
- Introduction 8
- Optimized Usability 9
- Front Panel Overview 10
- Top Panel Overview 11
- 15:44:03 03,10,08 12
- Instrument Markings 13
- 1Overview 14
- 8 N9340A User’s Guide 14
- Getting Started 15
- Safety Considerations 17
- 1 Getting Started 18
- 12 N9340A User’s Guide 18
- Power Requirements 19
- AC Power Cords 20
- Environmental Requirements 21
- Electrical Requirements 21
- Working with Batteries 22
- Charging a Battery 23
- Power on your N9340A 24
- • turn off backlight 25
- • turn off screen display 25
- Entering Data 27
- Some Helpful Tips 29
- Saving Multiple Test Setups 30
- Upgrading Firmware 31
- Adding an option 31
- System Setting 33
- Visual and Audio Adjustment 34
- Ext Input 36
- Quick saving a setup 37
- Quick recalling a setup 37
- Parameters) 37
- File Types 38
- Saving a file 39
- Viewing file list 40
- Deleting a file 41
- Loading a file 41
- Show System 42
- Show Error 43
- Factory Default Settings 45
- 4System Setting 46
- 40 N9340A User’s Guide 46
- Making Measurements 47
- Measuring Multiple Signals 48
- Directional 50
- Signal generator 50
- Resolving Small Signals 52
- Hidden by Large Signals 52
- Measuring a Low-Level Signal 53
- Increased Sweep Time 56
- Trace Av eragi ng 57
- One-button Power Measurement 65
- Measuring ACPR 66
- Measuring Channel Power 67
- Channel Bandwidth 68
- Low-pass Filter 71
- N9340A 73
- Making Measurements 4 75
- N9340A User’s Guide 69 75
- Calibration Routine 76
- 4 Making Measurements 82
- 76 N9340A User’s Guide 82
- Key Reference 83
- Amplitude 84
- Scale/DIV 85
- Scale Type 85
- Ref Offset 86
- Y Axis Units 86
- Spectrum Analyzer 87
- Track ing G ener ator 87
- Amptd Step 88
- Amptd Offset 88
- Normalize 88
- Power Meter 90
- Meas Disp 91
- Meas Setup 92
- Avg Type 96
- In non-zero spans: 98
- In zero span: 98
- In FFT Mode 99
- Sweep Mode 99
- Single Sweep 100
- CAU-CAUTION 102
- Frequency 103
- Peak Search 107
- • Freq Count 108
- Marker Trace 109
- Last Span 111
- Clear Write 112
- Max Hold 112
- Minimum Hold 113
- Detector 113
- Save Trace 116
- Recall Trace 116
- Limit Line 117
- Limit Pattern 117
- Set Pattern 117
- Limit Type 117
- Save Pattern 118
- Recall Pattern 118
- SCPI Command Reference 119
- SCPI Language Basics 120
- Basic Knowledge Requirement 121
- Command Categories 121
- Command Syntax 121
- Standard Notations 122
- Default unit of parameters 123
- Common Commands 124
- CALCulate Subsystem 125
- Control Limit line Buzzer 126
- Control Limit Line Testing 126
- Set Limit Line Y-axis value 126
- Control Limit Pattern Testing 127
- Define Limit Pattern Values 128
- CALCulate:MARKer Subsection 129
- Marker Function 130
- Marker Mode 131
- Marker On/Off 132
- Marker to Trace 132
- Marker readout: X Value 133
- Marker readout: Y Value 133
- DEMOdulation Subsystem 134
- DISPlay Subsystem 135
- Vertical Axis Scaling 137
- Display Mode 137
- Contrast 138
- Brightness 138
- INITiate Subsystem 139
- Select One button measurement 140
- MEASure Subsystem 141
- ACPR Subsection 142
- Low Adjacent Channel Power 143
- Upper Adjacent Channel Power 143
- Channel Power Subsection 144
- SENSe Subsystem 145
- Turn Averaging On/Off 146
- Set the Average Count 146
- [:SENSe]:BANDwidth Subsection 147
- Video Bandwidth Automatic 148
- [:SENSe]:DETector Subsection 149
- FREQuency Subsection 150
- Center Frequency Step Size 151
- Frequency Span 151
- Full Frequency Span 151
- Zero Frequency Span 151
- Last Frequency Span 152
- Start Frequency 152
- Stop Frequency 152
- [:SENSe]:POWer Subsection 153
- SWEep Subsection 154
- SYSTem Subsystem 155
- TRACe Subsystem 156
- Tracking Generator Subsystem 157
- Amplitude Step 158
- Amplitude Offset 158
- Storing as reference 158
- Normalization 159
- Normalization Reference Level 159
- Reference Trace 160
- TRIGer Subsystem 161
- UNIT Subsystem 162
- Error Messages 163
- Error Message List 164
- Menu Map 167
- 8Menu Map 168
- 162 N9340A User’s Guide 168
- Menu Map 8 169
- N9340A User’s Guide 163 169
- 164 N9340A User’s Guide 170
- N9340A User’s Guide 165 171
- 166 N9340A User’s Guide 172
- N9340A User’s Guide 167 173
- 168 N9340A User’s Guide 174
- N9340A User’s Guide 169 175
- 170 N9340A User’s Guide 176
- *N9340-90001* 179
Manuais e produtos relacionados com Multímetros Agilent Technologies N9340A
(32 páginas)
(84 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais