Agilent Technologies E8462A Manual do Utilizador Página 73
- Página / 156
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Agilent E8462A Relay Multiplexer Command Reference 71
ABORt
The ABORt command stops a scan in progress when the scan is enabled via the
interface and the trigger source is
TRIGger:SOURce BUS or
TRIGger:SOURce HOLD.
Subsystem Syntax ABORt
Comments ABORt Actions: The ABORt command terminates a scan in progress by causing the
switchbox to no longer wait for a trigger. When the
ABORt command is executed,
the last channel switched during the scan remains in the position.
Stopping Scan Enabled Via Interface: When a scan is enabled via an interface,
an interface clear command (
CLEAR 7) can be used to stop the scan. When the scan
is enabled via the interface and
TRIG:SOUR BUS or HOLD is set, you can use
ABORt to stop the scan.
Restarting a Scan: Use the
INITiate command to restart the scan.
Related Commands:
ARM, INITiate:CONTinuous, [ROUTe:]SCAN, TRIGger
Example Stopping a Scan with ABORt
This example stops a (continuous) two-wire scan in progress in a single-module
switchbox.
TRIG:SOUR BUS
Trigger command will be via backplane
(bus) interface (*TRG command
generates trigger).
INIT:CONT ON
Set continuous scanning.
SCAN (@10000:10007)
Scan channels 0 to 7.
INIT
Starts scan, closes channel 0.
.
.
.
ABOR
Abort scan in progress.
- *E8462-90000* 1
- Contents 3
- Certification 7
- Safety Symbols 8
- WARNINGS 8
- Documentation History 8
- Trademarks 8
- Declaration of Conformity 9
- Multiplexer 13
- Optional Terminal 14
- Warnings and Cautions 16
- Setting the Logical 17
- Setting the Interrupt 18
- Priority Line 18
- Protection 18
- Resistors 18
- Connecting Field Wiring 20
- Front Panel 21
- Connector Pin-Out 21
- 1-Wire Mode 22
- 2-Wire Mode 23
- 3-Wire Mode and 4-Wire Mode 24
- Connecting the 25
- Analog Bus 25
- Option 015 Ribbon Cable 27
- Connector Terminal 27
- Attaching a Terminal 30
- Block to the Multiplexer 30
- Programming the Multiplexer 31
- CARD NUMBER 01 32
- CARD NUMBER 02 32
- CARD NUMBER 03 32
- Channel Numbers 33
- Ranges, and Lists 33
- Initial Operation 34
- Example: Reset 35
- Self Test, Module 35
- ID, and Close 35
- Using the Multiplexer 37
- Switching or Scanning 38
- Performing 39
- Measurements via 39
- 1-Wire @ Ter0 40
- 2-Wire @ Ter0 and 41
- Other Modes 42
- Using the Multiplexer 41 43
- Mode: WIRE1x2 and 44
- Mode: WIRE1x4 45
- WIRE2x4 45
- Mode: WIRE1x8 46
- WIRE2x8 46
- Scanning Channels 47
- Synchronizing the 48
- Multiplexer with a 48
- Multimeter 48
- Using the Multiplexer 51 53
- BUS trigger (GET or *TRG) to 53
- Recalling and Saving States 54
- Detecting Error Conditions 55
- Function Mode Topologies 56
- WIRE1 Mode Topology 57
- WIRE2 Mode Topology 58
- WIRE3 and WIRE4 Mode Topology 59
- WIRE1X2 Mode Topology 60
- WIRE1X4 Mode Topology 61
- WIRE1X8 Mode Topology 62
- WIRE2X2 Mode Topology 63
- WIRE2X4 Mode Topology 64
- WIRE2X8 Mode Topology 65
- WIRE4X2 Mode Topology 66
- WIRE4X4 Mode Topology 67
- 66 Using the Multiplexer 68
- Command Reference 69
- Commands 70
- Variable Command 71
- SCPI Command Reference 72
- Subsystem Syntax ABORt 73
- ARM:COUNT 74
- 74
- ARM:COUNt? 74
- Parameters 75
- Example Query Number of Scans 75
- DIAGnostic 76
- DIAGnostic:INTerrupt:TIMer 78
- DIAGnostic:INTerrupt:TIMer? 78
- DIAGnostic:SCAN:DELay 79
- DIAGnostic:SCAN:DELay? 79
- DISPlay:MONitor:CARD 80
- DISPlay:MONitor:CARD? 80
- DISPlay:MONitor[:STATe] 81
- DISPlay:MONitor[:STATe]? 82
- INITiate 83
- INITiate:CONTinuous? 84
- INITiate[:IMMediate] 84
- OUTPut:ECLTrgn[:STATe] 85
- OUTPut:ECLTrgn[:STATe]? 86
- OUTPut[:EXTernal][:STATe] 86
- OUTPut[:EXTernal][:STATe]? 87
- OUTPut:TTLTrgn[:STATe] 87
- OUTPut:TTLTrgn[:STATe]? 88
- [ROUTe:] 89
- [ROUTe:]CLOSe? 92
- [ROUTe:]FUNCtion 92
- [ROUTe:]FUNCtion? 94
- [ROUTe:]OPEN 94
- [ROUTe:]OPEN? 97
- [ROUTe:]SCAN 98
- ROUT:FUNC command 99
- [ROUTe:]SCAN:MODE 100
- [ROUTe:]SCAN:MODE? 101
- [ROUTe:]SCAN:PORT 101
- [ROUTe:]SCAN:PORT? 102
- Subsystem Syntax STATus 103
- STATus:OPERation[:EVENt]? 105
- STATus:OPERation:CONDition? 105
- STATus:OPERation:ENABle 105
- STATus:OPERation:ENABle? 105
- STATus:PRESet 106
- SYSTem:CDEScription? 107
- SYSTem:CPON 108
- SYSTem:CTYPe? 108
- SYSTem:ERRor? 109
- TEST:NUMBer? 110
- TRIGger[:IMMediate] 112
- TRIGger:SLOPe 112
- TRIGger:SLOPe? 113
- TRIGger:SOURce 113
- TRIGger:SOURce? 115
- 488.2-1987 116
- SCPI Command Quick Reference 117
- Application Examples 119
- Reset Conditions 120
- The Scanning Voltmeter 121
- Making Measurements 122
- Select range 125
- Agilent E8462A Specifications 127
- Input Characteristics 128
- AC Performance 129
- (Typical) 129
- Register-Based Programming 131
- A16 Address Space 132
- Outside the Command 132
- Inside the Command 133
- Module or Mainframe 133
- Register Descriptions 135
- Device Type 136
- Register 136
- Status/Control 136
- • Set the SYSFAIL bit to “1” 137
- • Wait 10 nanoSeconds 137
- Relay Control 138
- Registers 138
- Timer Control 140
- Program Timing and Execution 141
- Using a Multimeter 142
- Programming Example 143
- Error Handling Function 145
- Error Messages 147
- 146 Error Messages 148
- Index 147 149
- 148 Index 150
- Index 149 151
- 150 Index 152
- Index 151 153
- 152 Index 154
- Index 153 155
- 154 Index 156
Manuais e produtos relacionados com Multímetros Agilent Technologies E8462A
Multímetros Agilent Technologies 437B Guia do Utilizador
(261 páginas)
(261 páginas)
Multímetros Agilent Technologies 1912A Manual de Serviço
(142 páginas)
(142 páginas)
(4 páginas)
Multímetros Agilent Technologies 6050A Especificações
(101 páginas)
(101 páginas)
(20 páginas)
Multímetros Agilent Technologies 8481B Especificações
(154 páginas)
(154 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais