Agilent Technologies 6051A Instruções de Operação Página 57
- Página / 97
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Language Dictionary
57
RES:RANGe Channel-Specific Resistance Command/Query
Description
This command selects the full-scale resistance range of the electronic load. Programming
any value equal to or greater than zero (
≥
0) and less than or equal to (
≤
) the maximum
value of the lowest range automatically selects that range. Programming any value greater
than the minimum range and less than or equal to (
≤
) the maximum value of the middle
range automatically selects that range. There is no overlap between the low and middle
ranges. Programming a value greater than the maximum value of the middle range
automatically selects the highest range
Note
Whenever the electronic load changes resistance range, the input momentarily goes into
the OFF (minimum current) state.
The values of the input resistance (IMMediate, TRIGgered and TLEVel) are adjusted as
follows:
If Then
The existing resistance setting is The resistance value does not change.
within the new range.
The existing resistance value is The resistance is set to the closest limit of
not within the new range. the new range.
For example, assume the Agilent 6060A Electronic Load; is in the 10000-ohm range and
the input resistance (RES:LEV) is 2000 ohms. Switching to the 1000-ohm range will
reduce the resistance to the closest limit of that range, or 1000 ohms. However, if another
parameter (such as RES:TRIG) was already within the new range (e.g., 500 ohm), then it
will remain at that level in the new range. When switching between two ranges that
overlap, the accuracy of the programmed value may be compromised because of reduced
resolution when going from a lower to a higher range.
Command Syntax
RESistance:RANGe <NRf+>
Parameters
See Table 4-1 and the Operating Manual of the electronic load model.
Value Coupling
This command affects the following parameters:
RES:LEV RES:TLEV
Examples
RES:50 Set resistance 50 ohms.
RES:RANG 1; :TRIG 45E-3 Change range to 1 ohm and set Triggered resistance to 45
milliohms. The main resistance will drop to 1 ohm and remain there until a trigger occurs.
Query Syntax
RES:RANG?
RES:RANG? MAX RES:RANG? MIN
Returned Parameters
<NR3> RES:RANG? returns the present resistance range in ohms. RES:RANG?
MAX and RES:RANG? MIN return the maximum and minimum programmable ranges
for the electronic load.
Related Commands
RES:[LEV] RES:TRIG RES:TLEV
- PROGRAMMING MANUAL 1
- PRINTING HISTORY 2
- CONTENTS 3
- CONTENTS (continued) 4
- Introduction 7
- How To Use This Guide 8
- What You Should Already Know 8
- Introduction To HPSL 11
- HPSL Keywords 12
- Common Commands 15
- Introduction To Programming 17
- Traversing The Command Tree 20
- HPSL Compatibility 23
- Value Coupling 23
- Programming Examples 24
- Language Dictionary 29
- *CLS Clear Status Command 30
- Syntax Diagram 31
- *IDN? Identification Query 33
- *RST Reset Command 36
- *SAV Save Command 37
- *STB? Read Status Byte Query 38
- *TST? Self Test Query 39
- Root-Level Commands 40
- Syntax Diagram 43
- Remember 61
- Error Messages 79
- Command Parameters Type 81
- Status Reporting 83
- Status Reporting 84
- Channel Summary 85
- Questionable Status 86
- Output Queue 87
- Standard Event Status 87
- Operation Status 88
- Status Byte Register 89
- Index (continued) 92
- Manual Updates 97
Manuais e produtos relacionados com Multímetros Agilent Technologies 6051A
Multímetros Agilent Technologies 53230A Especificações
(260 páginas)
(260 páginas)
Multímetros Agilent Technologies 6051A Manual de Serviço
(116 páginas)
(116 páginas)
Multímetros Agilent Technologies 34420A Especificações
(294 páginas)
(294 páginas)
(22 páginas)Sony MDR-EX57LP Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Audio Sony MDR-EX57LP.
Wir stellen 1 PDF-Handbücher Sony MDR-EX57LP zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comentários a estes Manuais