Agilent Technologies E1345A Manual do Utilizador Página 16
- Página / 93
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Getting Started 17Chapter 1
Initial Operation
Use the following program example to verify initial multiplexer operation
by closing a channel and querying channel closure. The example first resets
the switchbox and then closes channel 02 of a single multiplexer module
(card number 1) in the switchbox. The program next queries the channel
closure state. A returned "1" shows that the command to close the channel
has been sent to the switchbox. A returned "0" shows that the command to
close the channel has not been sent to the switchbox.
The computer used in the example is an Series 200/300 computer with
BASIC as the program language. The computer interfaces to the mainframe
using the General Purpose Interface Bus (GPIB)
1
. The GPIB interface select
code is 7, the primary address is 09, and the secondary address is 14. Refer
to the 75000 Series B Installation and Getting Started Guide for addressing
information.
Example: Reset the switchbox and close channel 02
10 OUTPUT 70914;"*RST"
Opens all channels.
20 OUTPUT 70914;"CLOS (@102)"
Close channel 02.
30 OUTPUT 70914;"CLOS? (@102)"
Query channel 02 state.
40 ENTER 70914;Value
Enter results into Value.
50 PRINT Value
Display result.
60 END
1. GPIB is Agilent Technologies’ implementation of IEEE-488.2
- *E1345-90005* 1
- Contents 3
- 2 Contents 4
- Contents 3 5
- 4 Contents 6
- Safety Symbols 8
- WARNINGS 8
- Documentation History 8
- Declaration of Conformity 9
- Getting Started 10
- Getting Started 13Chapter 1 12
- • specify the card number 13
- • specify the channel number 13
- Getting Started 15Chapter 1 14
- SCPI Command 15
- Format Used in This 15
- Initial Operation 16
- Chapter 2 18
- Warnings and Cautions 18
- Connecting Field Wiring 19
- Wiring a Terminal Module 20
- Connecting the Analog Bus 21
- Setting the Card ID 22
- Using the Scanning 23
- Voltmeter 23
- Configuration 23
- Connecting User Inputs 28
- Chapter 3 30
- Using This Chapter 30
- Multiplexer Commands 30
- Example: Connect 31
- Channels 02 and 09 to 31
- Making Measurements 33
- Channels 02 and 10 to 34
- Tree Terminals for 4-Wire 34
- Ohms Measurements 34
- Example: Making Voltage 35
- Measurements by 35
- Scanning 35
- (E1344A/47A Modules Only) 38
- Chapter 4 40
- Figure 4-1. Scanning Commands 41
- Example: Scanning With 43
- External Devices 43
- Example: Scanning 44
- "Event In" Ports 44
- Using the Scan Complete Bit 45
- Chapter 5 46
- Command Types 46
- SCPI Command Reference 48
- Subsystem Syntax ABORt 49
- • *RST Condition: ARM:COUNt 1 50
- 1 and MAX returns 32767 51
- Parameters 51
- Comments 51
- :MONitor:CARD 52
- :MONitor[:STATe] 53
- INITiate 54
- :CONTinuous? 55
- [:IMMediate] 55
- [ROUTe:] 57
- SCAN:MODE? 61
- SCAN:PORT 61
- :OPERation:ENABle 62
- :OPERation[:EVENt]? 63
- :CDEScription? 64
- :SOURce? 69
- IEEE 488.2 Common Commands 70
- Command Quick Reference 71
- 16-Channel Relay Multiplexer 72
- Specifications 72
- Relay Life 74
- End of Life Detection 74
- Replacement Strategy 74
- Appendix B 76
- Computer 77
- Configurations 77
- = 1FC000 79
- 08, is register number 4 79
- Reading the 80
- Registers 80
- Writing to the 81
- Error Messages 84
- Symbols: 86
- C (continued) 87
- Index 89 88
- 90 Index 89
- R (continued) 90
- S (continued) 91
- Index 93 92
- 94 Index 93
Melissa 240-100 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Odkurzacze Melissa 240-100.
Dostarczamy 1 pdf podręczników Melissa 240-100 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Comentários a estes Manuais