Agilent Technologies N4010A Especificações

Getting Started Guide Wireless Connectivity Test SetN4010AManufacturing Part Number: N4010- 90044Printed in UKNovember 2005© Copyright Agilent Technol

Getting StartedWelcomeChapter 12WelcomeWelcome to the Agilent Technologies Wireless Connectivity Test Set’s Getting Started Guide. This guide is for u

Getting StartedIntroductionChapter 1 3IntroductionThe Agilent N4010A Wireless Connectivity Test Set is a one- box test set for, Bluetooth and WLAN, mo

Getting StartedIntroductionChapter 14Table 1- 1 Test Set Control Differences Between Bluetooth and WLANFunction Bluetooth Test Bluetooth EDR TestWLAN

Getting StartedThis guide helps you to:Chapter 1 5This guide helps you to:• initially inspect the Test Set.• know the PC minimum requirements.• adjust

Getting StartedInitial InspectionChapter 16Initial InspectionPlease inspect the shipping container for damage. If the shipping container or packaging

Getting StartedMinimum PC RequirementsChapter 1 7Minimum PC RequirementsThe PC must meet the following minimum requirements:• Windows® 2000 (SP4 or gr

Getting StartedAdjusting the Carrying HandleChapter 18Adjusting the Carrying Handle Adjust the carrying handle to carry the Test Set or view the displ

Getting StartedTurning the Test Set OnChapter 1 9Turning the Test Set OnCAUTION The Test Set has an autoranging power supply. Ensure the supply voltag

Getting StartedTurning the Test Set OnChapter 110NOTE If the test set has been stored in extremely cold conditions, beyond its normal operating range,

Getting StartedTurning the Test Set OnChapter 1 11What Can Go Wrong?See this Do thisRed LED not lit Check that power is supplied to the test set.Check

iiGeneralThe material contained in this document is provided “as is,” and is subject to being changed, without notice, in future editions. Further, to

Getting StartedTurning the Test Set OnChapter 112

Chapter 2 132 Making Your First Measurements

Making Your First MeasurementsSelecting the Application ModeChapter 214Selecting the Application ModeThe purpose of this guide is to allow you to conf

Making Your First MeasurementsRunning a Confidence Check on the Front Panel (Bluetooth)Chapter 2 15Running a Confidence Check on the Front Panel (Blue

Making Your First MeasurementsRunning a Confidence Check on the Front Panel (Bluetooth)Chapter 216Figure 2- 3 Typical Configure Link Screen when ACL i

Making Your First MeasurementsRunning a Confidence Check on the Front Panel (Bluetooth)Chapter 2 17necessary, as shown in Figure 2-4.9. Press the so

Making Your First MeasurementsRunning a SCPI Confidence CheckChapter 218Running a SCPI Confidence CheckStep 1. Install the Agilent I/O Libraries Suite

Making Your First MeasurementsRunning a SCPI Confidence CheckChapter 2 19Step 3. Sending SCPI commands1. In the Agilent Connection Expert program, cli

Making Your First MeasurementsRunning a WLAN Confidence CheckChapter 220Running a WLAN Confidence CheckTo operate a WLAN Confidence Check, your N4010A

Making Your First MeasurementsRunning a WLAN Confidence CheckChapter 2 21Step 1. Install the N4010A Wireless LAN Test Suite.1. Insert the CD Wireless

iiiLegal InformationCertificationAgilent Technologies certifies that this product met its published specifications at the time of shipment from the

Making Your First MeasurementsRunning a WLAN Confidence CheckChapter 222Step 3. Rename the Test Set in Connection Wizard.1. In the Agilent Connection

Making Your First MeasurementsRunning a WLAN Confidence CheckChapter 2 234. Click on the Demo tab.5. Click on Run Demo.6. The display shows a loopback

Making Your First MeasurementsRunning the Graphical Measurement Application (GMA) N4017A.Chapter 224Running the Graphical Measurement Application (GMA

Making Your First MeasurementsRunning the Graphical Measurement Application (GMA) N4017A.Chapter 2 25Step 1. Installing the Bluetooth GMA1. Insert the

Making Your First MeasurementsRunning the Graphical Measurement Application (GMA) N4017A.Chapter 226Step 2. Connecting the Test SetRefer to “Connectin

Making Your First MeasurementsRunning the Graphical Measurement Application (GMA) N4017A.Chapter 2 275. Use the Instrument Selector to locate your Tes

Making Your First MeasurementsRunning the Graphical Measurement Application (GMA) N4017A.Chapter 228Figure 2- 13 Typical Connection Control Screen10.

Making Your First MeasurementsRunning the Graphical Measurement Application (GMA) N4017A.Chapter 2 2915. In the Control menu, click Run Single.16. The

Making Your First MeasurementsConnecting USB, GPIB or LANChapter 230Connecting USB, GPIB or LANThe Test Set can be remotely controlled by USB, GPIB (I

Making Your First MeasurementsConnecting USB, GPIB or LANChapter 2 31Connecting by USBThe USB interface requires no front panel configuration. USB ope

ivSafety NoticesThis guide uses warnings and cautions to denote hazardsWARNING Warning denotes a hazard. It calls attention to a procedure, which if n

Making Your First MeasurementsConnecting USB, GPIB or LANChapter 232Connecting by GPIB Changing the GPIB AddressThe GPIB address is an integer between

Making Your First MeasurementsConnecting USB, GPIB or LANChapter 2 33Figure 2- 15 Typical Connection Expert Screen showing GPIB Connection4. The Test

Making Your First MeasurementsConnecting USB, GPIB or LANChapter 234Connecting by LAN The Test Set has two LAN operating modes.• Dynamic Host Configu

Making Your First MeasurementsConnecting USB, GPIB or LANChapter 2 35DHCP ModeIn DHCP mode the IP Address, Subnet Mask and Default Gateway values are

Making Your First MeasurementsConnecting USB, GPIB or LANChapter 236Configuring the Connection Expert1. Run the Connection Expert program. It can be o

Making Your First MeasurementsConnecting USB, GPIB or LANChapter 2 376. In the pop up screen, shown in Figure 2-18, select the IP Address link.7. Ente

Making Your First MeasurementsConnecting USB, GPIB or LANChapter 238Static IPIn static mode you must set up the IP Address, Subnet Mask, and Default G

Making Your First MeasurementsRack Mounting the Test SetChapter 2 39Rack Mounting the Test SetDisconnect Device RequirementsIn rack mounting operation

Making Your First MeasurementsRack Mounting the Test SetChapter 2403. Fit the Rack Mount Flanges.(Parts available separately: 5063-9241).Ready for ins

Chapter 3 413Regulatory Information

vDO NOT operate the product in an explosive atmosphere or in the presence of flammable gasses or fumes.DO NOT perform procedures involving cover or

Regulatory InformationGeneral SpecificationsChapter 342General SpecificationsEnvironmentalPhysical SpecificationsPower RequirementsCooling Requirement

Regulatory InformationGeneral SpecificationsChapter 3 43CleaningUse a soft, clean, damp cloth to clean the front- panel and side covers.UsageThis Test

Regulatory InformationCompliance and MarkingsChapter 344Compliance and MarkingsElectromagnetic Compatibility (EMC)This product conforms with the prote

Regulatory InformationCompliance and MarkingsChapter 3 45MarkingsThe following markings can be found on the rear panel.The CE mark shows that the prod

Regulatory InformationCompliance and MarkingsChapter 346This product complies with the WEEE Directive (2002/96/EC) marking requirements. The affixed l

Regulatory InformationRegulatory InformationChapter 3 47Regulatory InformationSound EmissionHerstellerbescheinigungDiese Information steht im Zusammen

Regulatory InformationDeclaration of ConformityChapter 348Declaration of ConformityDECLARATION OF CONFORMITY According to ISO/IEC Guide 22 and CEN/CEN

Regulatory InformationResponsibilities of the CustomerChapter 3 49Responsibilities of the CustomerThe customer shall provide:• Access to the products

Regulatory InformationAgilent Sales and Service OfficesChapter 350Agilent Sales and Service OfficesIn any correspondence or telephone conversations, r

viWARNING Appliance coupler (mains input power cord) is the power disconnect device. Do not position the Test Set such that access to the coupler is i

Contents vii1. Getting StartedWelcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ContentsviiiMarkings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Regulat

Chapter 1 11Getting Started