Agilent Technologies E8267D PSG Manual do Utilizador Página 1

Agilent E8267CPSG Vector Signal GeneratorsData SheetAll specifications and characteristics apply over a 0 to 55 °C range (unless otherwise stated) and

10Maximum deviation N x 8 MHzResolution 0.1% of deviation or 1 Hz, whichever is greaterDeviation accuracy < ± 3.5% of FM deviation + 20 Hz(1 kHz ra

11Rate (typical 1 dB bandwidth)ALC on 1 kHz to 80 MHzALC off DC to 80 MHzExternal 1 input Sensitivity 0.5 V = 100%Input impedance 50 Ω (nominal) Modul

12Standard Standard Option 1E62> 3.2 GHz 500 MHz to 3.2 GHz 10 MHz to 3.2 GHzOn/off ratio 80 dB 80 dB (typical) 80 dBRise/fall times (Tr, Tf ) 10

13Internal pulse generatorModes Free-run, triggered, triggered with delay, doublet, and gated. Triggered with delay, doublet, and gatedrequire extern

14External I/Q inputsInput impedance switched 50 or 600 Ω (nominal) Input range1Minimum 0.1 Vrms, maximum 1VpeakFlatness ± 1 dB within ± 40 MHz of ca

15Channels 2 [I and Q]Resolution 16 bits [1/65,536]Baseband waveform memoryLength (playback) 64 megasamples (MSa)Length (storage) 1.2 gigasamples (G

16Measured multicarrier4 Carriers with 64 QAM at 10 Msym\s with 20 MHz spacing MultitoneNumber of tones 2 to 64, with selectable on/off state per ton

17Two-toneFrequency spacing 100 Hz to 80 MHz (symmetrical about carrier)IM distortion250 kHz to 3.2 GHz < –45 dBc for RF levels < 0 dBm (typica

18Measured EVMMeasured spectral re-growth 5 GHz carrier with 16 QAM signal at 10 Msym/sFrame trigger delay controlRange 0 to 1,048,575 bitsResolution

19RF output frequency range: 3.2 to 20 GHzInputInput (baseband) frequency range DC to > 500 MHz (nominal) Input impedance 50 Ω (nominal) Recommende

2Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Frequency . . . . . . .

20Interfaces GPIB (IEEE-488.2,1987) with listen and talk, RS-232,and 10BaseT LAN interface.Control languages SCPI version 1997.0. Also will emulate mo

21External input 2 Drives either AM, FM, or ΦM. Nominal input impedance 50 or 600 Ω, damage levels are 5 Vrmsand 10 Vpeak.Pulse/trigger gate input A

22Stop sweep In/Out Open-collector, TTL-compatible input/output. In ramp sweep operation, provides low level (nominally 0 V) duringsweep retrace and b

23I and Q outputs Outputs the analog I/Q modulation signals from the internalbaseband generator. Nominal output impedance 50 Ω ,DC-coupled. Damage lev

www.agilent.com/find/psgwww.agilent.com/find/basebandstudiowww.agilent.com/find/signalstudioPSG Signal Generators, BrochureLiterature number: 5989-132

3Range1 Option 520 250 kHz to 20 GHzResolutionCW 0.001 HzAll Sweep Modes 0.01 Hz2Accuracy Aging rate ± temperature effects± line voltage effectsSwi

4Operating modes Step sweep of frequency or amplitude or both (start to stop)List sweep of frequency or amplitude or both (arbitrary list)Sweep rangeF

5Output Power1(dBm)Frequency range 250 kHz to 3.2 GHz2–130 to +13250 kHz to 3.2 GHz (with Option 1E6)2–130 to +10> 3.2 to 20 GHz3–130 to +18Step at

620 GHz level accuracy Resolution 0.01 dBTemperature stability 0.01 dB/ °C (typical)User flatness correctionNumber of points 2 to 1601 points/tableN

7Harmonics1(dBc at +10 dBm or maximum specified output power, whichever is lower)< 1 MHz –27 dBc (typical)1 MHz to 2 GHz –27 dBc> 2 GHz to 20

8Option UNR: Enhanced SSB phase noise (CW) Offset from carrier (dBc/Hz)Frequency 100 Hz 1 kHz 10 kHz 100 kHzspec (typical) spec (typical) spec (typi

9Measured standard vs. Option UNR at 10 GHz Measured AM noise at 10 GHz1. Calculated from phase noise performance in CW mode only at +3 dBm. For other