Agilent Technologies 8590 L-Series Guia do Utilizador Página 218
- Página / 371
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
CLEAR
WRITE B
erases any data previously stored in trace B and continuously displays any
signals detected during the sweep of the spectrum analyzer. This function is
activated at power on and by pressing (PRESET_).
Changing the trace mode of trace C to clear write or minimum hold can change
the trace mode of trace B. If trace B is in clear-write mode or maximum-hold
mode when trace C is changed to clear write or minimum hold, the trace mode
of trace B is changed to store blank.
The following table shows the trace mode of trace B before and after changing
trace C to clear-write or minimum-hold trace mode.
Trace Mode of Trace B Trace Mode of Trace B
Before After
Clear write
Store blank
Maximum hold Store blank
View
View
Changing the trace mode of trace B to clear write or maximum hold can
change the trace mode of trace C. If trace C is in clear-write mode when trace
B is changed to clear write or minimum hold, the trace mode of trace C is
changed to minimum hold.
Trace Mode of Trace C Trace Mode of Trace C
Before After
Clear write Minimum hold
Minimum hold Minimum hold
View
View
Front-Panel Key Access:
[m)
Key
Descriptions
7.25
- Printed in USA July 1998 2
- Certification 4
- Warranty 4
- Assistance 4
- Safety Symbols 5
- General Safety Considerations 6
- Regulatory Information 7
- How to Order Manuals 8
- Contents 9
- Contents-2 10
- Contents-3 11
- Contents-6 14
- Contents-7 15
- Contents-8 16
- Contents-9 17
- Contents-l 0 18
- Preparing For Use 19
- 1-2 Preparing For Use 20
- Initial Inspection 21
- 1-4 Preparing For Use 22
- Checking the Fuse 23
- Power Cable 24
- 1-8 Preparing For Use 26
- Preparing For Use 1-9 27
- Electrostatic Discharge 29
- Reducing Damage Caused by ESD 30
- Getting Started 31
- SPECTRUM ANALYZER 32
- 2-2 Getting Started 32
- Getting Started 2-3 33
- 2-4 Getting Started 34
- Rear-Panel Features 35
- 2-6 Getting Started 36
- Getting Started 2-7 37
- Data Controls 38
- F I NE FOCUS ADJUSTMENT 39
- Getting Started 2-9 39
- Screen Annotation 40
- Menu and Softkey Overview 42
- Making a Measurement 43
- 2-14 Getting Started 44
- Measurement Summary 45
- Warm-Up Time 46
- (Option 010 or 011 only) 47
- 2-18 Getting Started 48
- Getting Started 50
- Getting Started 2-21 51
- Analyzer Battery Information 52
- Making Basic Measurements 53
- Bandwidth Function 54
- Making Basic Measurements 3-3 55
- Resolution Bandwidth Function 56
- SEARCH) 57
- 3-6 Making Basic Measurements 58
- Function 59
- 3-8 Making Basic Measurements 60
- 2. Press 61
- Making Basic Measurements 3-9 61
- I.121 GHz 65
- and AUTO ALL 68
- Distortion from the Analyzer 72
- SEARCH] 75
- NEXT PEAK . This places a 75
- Making Basic Measurements 76
- SCALE LOG LIN to underline 77
- Making Measurements 80
- 4-2 Making Measurements 81
- Making Measurements 4-3 82
- Menu, and MARKER 84
- Making Measurements 4-5 84
- 4-6 Making Measurements 85
- 4-8 Making Measurements 87
- && 88
- Making Measurements 4-9 88
- 4-10 Making Measurements 89
- 4-12 Making Measurements 91
- Making Measurements 4-13 92
- 4-14 Making Measurements 93
- TV TRIG sets 94
- 4-16 Making Measurements 95
- Reflection Calibration 96
- Measuring the Return Loss 97
- (Option 105 only) 98
- 4. Press 99
- 4-20 Making Measurements 99
- Coupling 100
- 4-22 Making Measurements 101
- Making Measurements 4-23 102
- 4-24 Making Measurements 103
- Figure 4-20 104
- (with Two Signals Present) 104
- 4-26 Making Measurements 105
- Making Measurements 4-27 106
- Making Measurements 4-29 108
- Making Measurements 109
- 0 000 ‘J 110
- 4-32 Making Measurements 111
- Gate Utility 112
- 4-34 Making Measurements 113
- Making Measurements 4-35 114
- Making Measurements 4-37 116
- Making Measurements 4-39 118
- 4-40 Making Measurements 119
- Making Measurements 4-41 120
- 4-42 Making Measurements 121
- Measurements 122
- 4-44 Making Measurements 123
- Making Measurements 4-45 124
- Menu , then press 125
- Making Measurements 4-47 126
- Channel Power Measurement 127
- Making Measurements 4-49 128
- Using Analyzer Features 129
- Use the Marker 130
- ‘I);tble 130
- Use the Peak 132
- To Save a State 134
- To Recall a State 134
- To Save a Trace 135
- To Recall a Trace 135
- 5-6 Using Analyzer Features 136
- register 138
- Using Analyzer Features 138
- To Enter a Prefix 140
- To Save a Display Image 142
- To Recall a Display Image 142
- Using Analyzer Features 5-15 143
- To Save a Program 144
- To Recall a Program 144
- LOAD FILE 145
- Using Analyzer Features 5-17 145
- Using Limit-Line Functions 146
- Limit-Line Functions 150
- Mid/Delt 151
- to editor 151
- Up/Low . With the upper 151
- Using Analyzer Features 5-23 151
- 5-24 Using Analyzer Features 152
- Using Analyzer Features 5-25 153
- Figure 5-7. Segment Types 155
- 5-28 Using Analyzer Features 156
- Using Analyzer Features 5-29 157
- 5-32 Using Analyzer Features 160
- FREQUENCY), START FREQ 161
- Using Analyzer Features 5-35 163
- Using Analyzer Features 5-39 167
- External Keyboard 168
- Using Analyzer Features 5-41 169
- Using the External Keyboard 170
- Printing and Plotting 172
- PRINTER 173
- PLOTS 174
- Printing and Plotting 175
- CONVERTER 176
- SPEr,TRIJM 176
- AIIAImYZER 176
- &POSITION SWITCH 176
- OFF (see 177
- Equipment 178
- SO that HPIB is underlined) 179
- COMPUTER/MODEM 186
- COPY DEV PRNT PLT 188
- 6-20 Printing and Plotting 191
- Key Descriptions 194
- Service Functions 195
- Analyzer Functions 197
- [FREQUENCY) 198
- Option 103 only 199
- 7-6 Key Descriptions 199
- Key Descriptions 7-7 200
- (AMPLITUDE) 201
- the HP 202
- Key Descriptions 7-9 202
- CFREQUENCY] 206
- 7-14 Key Descriptions 207
- Key Descriptions 7-15 208
- 7-16 Key Descriptions 209
- Key Descriptions 7-17 210
- PreVhiiz 211
- ‘dH..‘SVei’i’S.i 213
- 7-22 Key Descriptions 215
- Change Title or 216
- Change Prefix 216
- Key Descriptions 7-23 216
- 7-24 Key Descriptions 217
- (CONFIG) 220
- Key Descriptions 7-29 222
- 7-30 Key Descriptions 223
- [AMPLITUDE) 224
- 7-32 Key Descriptions 225
- Option 102 or 103 only 226
- Key Descriptions 7-33 226
- Key Descriptions 7-35 228
- MX80 SML LRG until SML 234
- Key Descriptions 7-41 234
- Option 713 237
- NORM OFF 237
- 7-44 Key Descriptions 237
- 7-46 Key Descriptions 239
- 7-48 Key Descriptions 241
- Key Descriptions 7-49 242
- 7-50 Key Descriptions 243
- Key Descriptions 7-51 244
- SEARCH and 246
- 7-54 Key Descriptions 247
- (MEAS/USERI) 248
- 7-56 Key Descriptions 249
- MK TRACK 250
- Key Descriptions 7-57 250
- Options 251
- Key Descriptions 7-59 252
- Key Descriptions 253
- Key Descriptions 7-61 254
- Key Descriptions 7-65 258
- 7-66 Key Descriptions 259
- Limit-line testing 260
- Reference level position 260
- Harmonic lock 261
- Key Descriptions 7-69 262
- Range for the HP 264
- Key Descriptions 7-71 264
- Key Descriptions 7-73 266
- Key Descriptions 7-75 268
- Key Descriptions 7-77 270
- time value of zero is the 271
- [SGLSWP_) 272
- (FREQUENCY] 274
- Option 105 only 275
- 7-82 Key Descriptions 275
- 7-84 Key Descriptions 277
- TIMEBASE 283
- AUTO MAN 283
- 7-90 Key Descriptions 283
- Key Descriptions 7-91 284
- YTF SPAN 285
- 7-92 Key Descriptions 285
- Key Descriptions 7-93 286
- Key Menus 287
- [AMPLITUDE] 288
- Key Menus 8-3 289
- Key Menus 8-5 291
- +-c:>= 292
- 8-8 Key Menus 294
- (RECALL] 295
- 8-12 Key Menus 298
- IS selected 299
- 8-14 Key Menus 300
- If You Have A Problem 301
- Check the Basics 302
- Read the Warranty 304
- Service Options 304
- How to Call Hewlett-Packard 304
- Service 306
- Original Packaging 306
- Other Packaging 306
- Error Messages 307
- (FREQUENCY) 308
- ANNOTATN ON OFF to clear, (U) 309
- ANALOG+ ON OFF. (U) 310
- 9-10 If You Have A Problem 310
- 9-14 If You Have A Problem 314
- DETECTOR PK SP NG . (U) 315
- 9-16 If You Have A Problem 316
- Accessories 317
- Measurement Personalities 318
- (Option 016) 322
- PDC/PHS/NADC/CDMA 327
- GSM/DCS1800 327
- AC Power Source 330
- AC Probe 330
- Burst Carrier Trigger 330
- Close Field Probes 331
- HP-IB Cable 331
- Memory Cards 331
- Parallel Interface Cable 331
- Service Requests 333
- Glossary 335
- Glossary-2 336
- Glossary-4 338
- Glossary-5 339
- Glossary-6 340
- Glossary-7 341
- Glossary-8 342
- Glossary-9 343
- Glossary-l 344
- Glossary-l 1 345
- Glossary-l 2 346
- Glossary-13 347
- Glossary-14 348
- Glossary-l 5 349
- Glossary-l 6 350
- Glossary-l 7 351
- FM span, 7-44 357
- Index-1 0 362
- Index-11 363
- Index-12 364
- Index-13 365
- Index-14 366
- Index-l 5 367
- Index-l 6 368
- Index-l 7 369
- Index-18 370
- YTF SPAN, 7-3, 7-92 371
Manuais e produtos relacionados com Multímetros Agilent Technologies 8590 L-Series
Multímetros Agilent Technologies 4294A Manual de Serviço
(249 páginas)
(249 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais