Agilent Technologies 4263B Manual de Instruções

○C Copyright 2009 Agilent Technologies Agilent 4263B LCR Meter Operation Manual Manual Change Agilent Part No. N/A Jun 2009 Change 1 Add

○C Copyright 2007 Agilent Technologies Change the Measurement Uncertainty value of 0 m Impedance Measurement Accuracy Test for 0 m Capacit

○C Copyright 2007 Agilent Technologies Change 7 Change the Measurement Uncertainty value of 0 m Impedance Measurement Accuracy Test for 0 m

○C Copyright 2007 Agilent Technologies Change 11 Change the Measurement Uncertainty value of 0 m Impedance Measurement Accuracy Test for 0

○C Copyright 2007 Agilent Technologies Change 14 Change the Measurement Uncertainty value of 1 m Impedance Measurement Accuracy Test for 1

○C Copyright 2007 Agilent Technologies Change 16 Change the Measurement Uncertainty value of 2 m Impedance Measurement Accuracy Test for 2

○C Copyright 2007 Agilent Technologies Change 19 Change the Measurement Uncertainty value of 4 m Impedance Measurement Accuracy Test for 4

Agilent 4263B LCR Meter Operation Manual Manual Change Agilent Part No. N/A July 2007 Change 1 Add the following steps to the step 2 of DC Bias Leve

マニュアル チェンジ 変更 1 DC バイアス・レベル確度試験の手順 2（ページ 9-9）に以下の手順を追加して下さい。 2-a. Freq を押して測定信号周波数を 100 kHz に設定します。 2-b. Level を押して測定レベルを 50 mV に設定します。 変更 2 DC バ

Agilent 4263B LCR Meter Operation Manual Manual Change Agilent Part No. N/A June 2007 Change 1 Add the following note to the “3-c. Turning On the 42

マニュアル チェンジ 変更 1 電源投入と電源周波数の設定の手順 3-c（ページ 1-11）に以下の注記を追加して下さい。 注記 AC 電源周波数の設定値が一致していない場合、測定誤差が増大する可能性があります。必ず AC 電源周波数を正しく設定して下さい。 変更 2 測定確度の条件（ペー

○C Copyright 2009 Agilent Technologies Change 4 Add TAR in 0 m Impedance Measurement Accuracy Test (Page 9-40 to 9-42) as follows. Impedanc

Safety SummaryWhen you notice any of the unusual conditions listed below, immediatelyterminate operation and disconnect the power cable.Contact your l

4263BCautionDo not apply DC voltage or current to the UNKNOWN terminals. Donot apply External DC bias voltage more than +2.5V. Doing so willdamage the

○C Copyright 2009 Agilent Technologies 1 μF 100 k D ±0.0176 ± 0.00032 55.73 Note 1: Result = Measurement – Calibrated Value of Standard

REGIONAL SALES AND SUPPORT OFFICESFor more information about Agilent Technologies test and measurement products, applications, services, andfor a curr

○C Copyright 2009 Agilent Technologies Measurement time: Med Test signal level: 500 mV Status PASS Standard Frequency [Hz] Param

○C Copyright 2009 Agilent Technologies Change 5 Add TAR in 1 m Impedance Measurement Accuracy Test (Page 9-43) as follows. Measurement: Cap

○C Copyright 2009 Agilent Technologies Change 6 Add TAR in 2 m Impedance Measurement Accuracy Test (Page 9-44) as follows. Measurement: Cap

○C Copyright 2009 Agilent Technologies Change 7 Add TAR in 4 m Impedance Measurement Accuracy Test (Page 9-45) as follows. Measurement: Cap

○C Copyright 2007 Agilent Technologies Agilent 4263B LCR Meter Operation Manual Manual Change Agilent Part No. N/A July 2008 Change 1 Cha

○C Copyright 2007 Agilent Technologies Change 3 Change the Measurement Uncertainty value of DC Bias Level Accuracy Test (Page 9-39) to the