Agilent-technologies System DC N5700 Manual do Utilizador descarregar pdf (Página 132)

1/11/12

The Declaration of Conformity has been removed and replaced with a

link to the web on page 2.

On page 90, under Environmental Conditions, information about

operating humidity has been updated, and the LED statement has

been removed. The Regulatory Compliance section has also been

updated with the latest requirements.

30/13

On pages 34 and 96, a warning about Safe-Start has been

added. On page 100, step #10 has been added. A warning has been

added to the verification test records.

1 2 ... 127 128 129 130 131 132

 1
Legal Notices 2
Safety Notices 3
In this Book 4
Contents 5
Quick Reference 7
Output Features 8
System Features 8
Programmable Functions 9
Model Ratings 9
DC AMPS 10
DC VOLTS 10
The Rear Panel – At a Glance 12
J2 Sense Connector 13
SW1 Setup Switch 13
Installation 15
General Information 16
Inspecting the Unit 17
Installing the Unit 17
Rack Installation 18
Cleaning 18
Connecting the Line Cord 19
Connecting the Load 21
CAUTION 22
Output Voltage Sensing 24
Local Sensing 25
Remote Sensing 25
Load Considerations 26
Inductive Loads 27
Parallel Connections 28
Setting up the Master Unit 29
Series Connections 30
J1 Connector Connections 32
Turn-On Check-Out 34
UVL Check 35
Constant Current Check 35
OCP Check 35
Normal Operation 36
Protection Functions 37
Under-Voltage Limit 38
Over-Current Protection 38
Over-Temperature Protection 39
Power-Fail Protection 39
Front Panel Lock-Out 39
Output On/Off Controls 40
Enable/Disable Terminals 41
Power Supply OK Signal 42
CURRENT LIMIT 44
PROGRAMMING 44
OUTPUT VOLTAGE 44
Connecting to the Interfaces 48
USB Interface 49
LAN Interface 49
Connecting to a Site LAN 50
LAN Communication 52
Using Telnet 53
Using Sockets 53
Using the Setup Utility 56
Message Unit 59
Queries 60
Common Commands 60
Command Terminators 60
Parameter Types 61
SCPI Command Completion 62
Language Reference 63
SCPI Command Summary 64
Calibration Commands 66
Measure Commands 67
Output Commands 68
Source Commands 69
Status Commands 71
STATus:PRESet 72
STATus:OPERation[:EVENt]? 72
STATus:OPERation:CONDition? 72
STATus:OPERation:ENABle? 72
System Commands 77
OUTP Off [SOUR:]VOLT:LIM 0 78
Trigger Commands 79
Programming Examples 81
Output Programming Example 82
Programming Examples 6 83
Trigger Programming Example 84
Appendix A 87
Specifications 87
Performance Specifications 88
Supplemental Characteristics 89
482.8+/-1.0mm 91
433+/-1.0mm 91
507.0+/-1.0mm 91
422.8+/-1.0mm 91
Appendix B 93
Verification and Calibration 93
Verification 94
Measurement Techniques 95
Constant Voltage Tests 96
CV Source Effect 97
CV Noise 97
Transient Recovery Time 98
Constant Current Tests 99
CC Source Effect 100
WARNING 101
60 V, from 1.25 A to 11.25 A 107
100 V, from 0.75 A to 6.75 A 109
200 V, from 0.25 A to 2.25 A 111
Calibration 113
Appendix C 115
Service 115
Types of Service Available 116
Repackaging for Shipment 116
Operating Checklist 116
Service Appendix C 117
Symptom Check Action 117
Error Messages 118
Appendix C Service 120
Command Errors (continued) 120
Appendix D 123
Compatibility 123
Differences – In General 124
Appendix D Compatibility 126
Command 126
Manual Updates 131

Comentários a estes Manuais

Sem comentários

Agilent-technologies System DC N5700 Manual do Utilizador Página 132

Comentários a estes Manuais

Manuais e produtos relacionados com Ferramentas Agilent-technologies System DC N5700