Agilent Technologies U4154A Manual de Serviço Página 12
- Página / 90
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
12 U4154A Logic Analyzer Service Guide
1 General Information
Accessories
One or more of the following accessories, sold separately, are
required to set up and operate the U4154A logic analyzer
module for testing and servicing it.
Probing Accessories
For information about probing accessories for logic analyzers
with 90- pin pod connectors, see the Probing Solutions for
Logic Analyzers Catalog, literature part number 5968- 4632E,
available on Agilent’s web site (www.agilent.com).
U4201A Pod Connector Cables
The Agilent U4201A 90- pin pod connector cable is used to
connect the U4154A module with the probes which then
connect to the DUT/SUT. You need four U4201A pod cables
for a U4154A module. Refer to the U4154A Logic Analyzer
Installation Guide to learn more about these cables.
Chassis and software
The U4154A logic analyzer requires:
• M9502A or M9505A Agilent AXIe chassis that provides
slots for installing the U4154A module.
• A host PC which is a laptop or a desktop PC with a PCIe
interface. The host PC connects to the Agilent AXIe
chassis via PCIe interface and is used to host all the
required software components of the U4154A module for
configuring, controlling, and using this module.
• Agilent Logic Analyzer software version 05.00 or higher to
configure, control, and use the U4154A module.
Refer to the U4154A Logic Analyzer Installation Guide to
learn more about AXIe chassis, host PC, and the Logic
Analyzer software installation.
- Agilent U4154A Logic 1
- Analyzer 1
- Additional Safety Notices 3
- Features 4
- Service Strategy 4
- Application 5
- In This Service Guide 6
- 4 Calibrating 8
- Contents 10
- General Information 11
- Accessories 12
- Chassis and software 12
- Specifications 13
- Characteristics 14
- Environmental Characteristics 15
- 1 General Information 16
- Performance Testing 17
- To set up the U4154A module 18
- To test the U4154A module 19
- To clean the module 19
- Testing U4154A Performance 21
- 3 Testing U4154A Performance 22
- One-card Module 22
- Multi-card Module 22
- Test Interval 22
- Test Record Description 23
- Test Equipment 23
- Perform the Self-Tests 24
- Set Up the Test Equipment 31
- Set up the oscilloscope 33
- Connect the Test Equipment 35
- Deskew the oscilloscope 39
- Test the U4154A Module 40
- Testing U4154A Performance 3 43
- Determine maximum clock rate 46
- Re-align a stray channel 52
- Tes t P od 1 54
- Configure the markers 55
- Tes t P od 2 58
- Tes t P ods 3 60
- Conclude the State Mode Tests 61
- Performance Test Record 62
- Calibrating 65
- Calibration Strategy 66
- Troubleshooting 67
- To use the flowcharts 68
- Troubleshooting 5 69
- Self-Test Descriptions 70
- Comparator Delay Test 72
- Comparator Zero-Hold Cal Test 72
- Comparator Calibrations Test 72
- Acquisition Memory Cell Test 72
- ATB (AXIe Trigger Bus) Test 73
- To run the self tests 74
- To exit the test system 75
- To test the cables 76
- 5 Troubleshooting 78
- Module or its cables 85
- To remove the U4154A module 86
- To replace the circuit board 87
Manuais e produtos relacionados com Multímetros Agilent Technologies U4154A
Multímetros Agilent Technologies 3070 Especificações
(18 páginas)
(18 páginas)
(84 páginas)Melissa 240-100 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Odkurzacze Melissa 240-100.
Dostarczamy 1 pdf podręczników Melissa 240-100 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Comentários a estes Manuais